StreetGlow LED Combo Kit - Manual

Installation Instructions
MOTORCYCLE
STARTER COMBO KIT
MOTORCYCLE
STARTER COMBO KIT
MCLKIT
Installation Instructions
CONTENTS
2 – 6” L.E.D. Strips
2 – 9” L.E.D. Strips
4 – L.E.D. Pods
2 – Red L.E.D. License Plate Light Bolts
1 – Distribution Block
1 – On / Off Switch
All necessary mounting hardware and
installation instruction
2 Year Limited Warranty
StreetGlow products are warranted against defects in the
material and /or workmanship according to the following
conditions and limitations:
1. Broken Glass, Labor and transportation are not covered
regardless.
2. Warranty is valid for 2 years from date of purchase.
3. Proof of purchase is required to validate warranty.
4. All warranty claims are to be handled by selling agents.
5. Accident, abuse, neglect, improper installation, not
used for its intended purpose are not covered. This
warranty is limited to replacing the defective part
without charge. The company in no event shall be held
responsible for any consequential or special damages.
This warranty gives you specific legal rights and you
may also have rights which vary from state to state.
WARNING!
StreetGlow products are recommended for show and
off-road use only. Laws concerning the use of aftermarket
lighting products may vary from state to state. For more
information, check with your local authority.
MOTORCYCLE STARTER COMBO KIT
MCLKIT
INSTALLATION INSTRUCTIONS FOR L.E.D.
STRIPS AND L.E.D. PODS
1. All mounting surface must be clean and free of all dirt,
wax, and oil prior to the installation. Wipe all areas with
the alcohol prep pad provided and let dry thoroughly.
2. Choose a location to mount the L.E.D. Strips. Installations
on flat and rigid surfaces, such as frame rails, gas tanks,
under saddle bags produce the best results
3. Choose location to mount the L.E.D. Pods. L.E.D. Pods
accent other bike parts and are best installed where the
light will reflect to highlight the engine (but not attached
to the engine itself ), fairings, etc.
4. Secure the Red L.E.D. License Plate Light Bolts to the
license plate bracket. DO NOT over tighten as over
tightening may cause bolt to crack.
WIRING CONNECTIONS
1. Choose a location to mount the on/off switch that
provides easy accessibility to the motorcycle’s battery.
Mount the on/off switch by drilling a ¼” hole in the
location that you have chosen to mount the switch.
2. Choose a location to mount the distribution block
preferably under the seat and accessible to the on/off
switch. Mount the distribution block using double face
3m tape(provided).
3. Connect the RED wire from the on/off switch to the (+)
12V positive side of the battery using a ring terminal
provided in the hardware kit.
4. Connect the BLACK WITH WHITE STRIPE wire from the
distribution block to the YELLOW wire from the on/off
switch using a butt connector, provided in the hardware
kit.
5. Connect the BLACK wire from the distribution block (-)
ground to the negative battery terminal using a ring
terminal provided in the hardware kit.
6. Each L.E.D. Strip and L.E.D. Pod has a BLACK WITH WHITE
STRIPE wire and a BLACK wire. Run all wires from the
locations of the L.E.D. Strips and L.E.D. Pods to the
distribution block. Connect the BLACK WITH WHITE
STRIPE (+) positive wires to positive terminal ports
numbered 1 through 4 on the back of the distribution
block. Repeat this procedure for each of the BLACK (-)
negative wires to negative terminal ports numbered 1
through 4 on the back of the distribution block.
INSTALLATION INSTRUCTIONS FOR L.E.D.
LICENSE PLATE LIGHT BOLTS
1. Each L.E.D. License Plate Light Bolt contains 2 wires; a
BLACK WITH WHITE STRIPE, the positive (+) wire and a
BLACK negative (-) wire.
2. Twist connect the two (+) positive BLACK WITH WHITE
STRIPE wires to each other and connect to a positive
terminal port numbered 1 through 4 on the back of the
distribution block.
3. Twist connect the two (-) negative BLACK wires to each
other and connect to a negative terminal port numbered
1 through 4 on the back of the distribution block.
OPTIONAL: A different wiring process will illuminate the LED
License Plate Light Bolts simultaneously with the
motorcycle’s brake or tail light,
Brake Light: Using a test light, find the power (+) wire of the
brake light circuit. Splice the 2 (+) positive black with
white stripe wires from the L.E.D. License Plate Light Bolts
to this wire. Follow the same procedures for the 2 black
(-) negative wires connecting to the ground wire of the
motorcycle brake light harness or to a chassis ground.
Tail Light: Using a test light, find the power (+) wire of the
tail light circuit. Splice the 2 (+) positive black with white
stripe wires from the L.E.D. Light Bolts to this wire. Follow
the same procedures for the 2 black (-) negative wires
connecting to the ground wire of the motorcycle tail light
harness or to a chassis ground.
NOTE 1: Use electrical tape (not supplied) to ensure a proper
weather tight connection.
NOTE 2: When routing the wires, keep them away from all
moving parts and areas of extreme heat (particularly
exhaust system components).