H-335 – Xylem H-335 User Manual
Page 12
1-8 Introduction
H-335
1.9 Installing the H-335 and setting the mechanical sensor offset
The tilt sensor in the H-335 has a physical ±40 calibrated range. This allows sufficient dynamic range to
measure a gate which opens up to 80 . To work properly, the sensor must be mechanically adjusted during
installation to preserve the available physical dynamic range. This is done by loosening two screws and
rotating the internal sensor assembly. The mechanical offset adjustments are made while monitoring the
SensorAngle parameter. This is the raw sensor reading with no adjustment for slope or offset. The
UserAngle parameter is processed with a slope and offset term to produce the more useful 0.0 to +80.0
reading for the data recorder.
With the gate closed the mechanical offset must be set near (but not beyond) one end of the sensor’s
measurement range. The proper setting depends on which gate arm the H-335 is installed and which side of
the I-beam the H-335 is mounted (see Figure 2). For example; with a gate which can open up to 70 and
which the inclinometer rotates clockwise (while facing the H-335 cover) as the gate opens, the sensor
should be rotated until SensorAngle reads ~ -35 . When this gate is fully open the raw SensorAngle will
read +35 . With the same gate but with the inclinometer installed such that it rotates counter-clockwise
(while facing the H-335 cover) as the gate opens, the sensor must be mechanically adjusted to +35 . When
this gate is fully open the raw SensorAngle will read -35 .
The H-335 fiberglass enclosure can be installed in any
position in the plane of rotation. If possible, locate the
connector on the bottom to prevent water from standing
on the connector. The internal ceramic sensor element
is symmetrical and will still make measurements if
installed upside down. However, if the sensor is upside
down, the calibration will be invalid, the slope will be
wrong and the output data confusing. Check to make
certain the wires exit the red plastic cover at the 2:00
o’clock position when the gate is in the center of its
travel arc.
- H-2191
- H-223
- H-264
- H-310
- H-312
- H-3301
- H-3342
- H-339
- H-340-CalKit
- H-340
- H-340SDI
- H-3521
- H-3531 FlashLite
- H-3551
- H-3553
- H-375 04101 WIND MONITOR-JR
- H-4161
- H-4191
- H-424MS V1.0
- H-424MS V1.1
- H-4271
- H-4280
- H-4400
- H-4401
- H-5223
- STORM 3 UPGRADE
- System 5000 BASIC Manual
- System 5000 User Manual
- DH-21
- BrazedPlate Heat Exchangers
- Heat Exchangers
- GL500 MULTICHANNEL DATA LOGGER
- 4046 ANALOG TO SDI-12 CONVERTER
- 4015 SDI-12 TO ANALOG CONVERTER
- iRIS-CAM Wastewater Security Camera
- SDI-12 Data Logger iRIS 220, iRIS 320, iRIS 350, iRIS 150, iRIS 300
- iRIS 150 GPRS DATALOGGERS
- iCE3 GPRS Variant
- GL500-2-1 Data Logger
- 3101 CONDUCTIVITY CONTROLLER
- 3675 pH CONTROLLER
- 378 TEMPERATURE CONTROLLER
- Expert 1400
- Expert 700
- Expert 7060_7070_Modbus
- Palmer & Bowlus flumes
- Parshall flumes
- Flow Converter 713
- MagFlux IP 68 Protection
- Magflux Electromagnetic Flow Meter
- MagFlux Day flow logger function
- Oxix Calibration
- Oxix Dissolved Oxygen Transmitter
- SuSix Sensor with Wiper - Wiper and Gasket Replacement Kit 206355
- SuSix Sensor with Wiper - Wiper and Gasket Replacement Kit 206356
- SuSix Turbidity and Suspended Solids Transmitter
- PHIX COMPACT pH and Redox Transmitter
- 701 PUMP CONTROLLER
- 712 PUMP CONTROLLER
- 704 PUMP CONTROLLER
- MY CONNECT Quick Guide
- MY CONNECT HMI display
- CONNECT Quick Guide
- CHATTER Base System install guide
- CHATTER Notification System configuration guide
- CHATTER Notification System install guide
- CHATTER RTU and E-mail
- CHATTER Base System Setup Tool Users Guide
- CHATTER Hardware Manual
- 531-532-533 DIGITAL INDICATORS
- 780 LIQUID SAMPLER
- 205546 Modbus Communication Modules for Displays
- 205547 Profibus Communication Modules
- 703 PUMP CONTROLLER
- Expert 800-900
- 702 MJK Comtroller
- 795 MJK Data Transmitter
- 795 II MJK Data Transmitter - GSM Modem
- SDI-12 RADAR
- STORM Central
- STORM 3 Basic Programming manual
- STORM 3 Getting Started Guide
- System 5000 Getting Started Guide
- XL-BASIC Programming Guide
- XL Series H-350XL
- CXA000 12 SWING SAMPLERS
- SP250 QUICK RELEASE WATER SAMPLER
- WS700 COMPOSITE/DISCRETE WATER SAMPLER
- WS700R REFRIGERATED WASTEWATER SAMPLER
- WS755 IMPROVED WASTEWATER/STORMWATER SAMPLER
- WS705 IMPROVED COMPOSITE/DISCRETE WATER SAMPLER
- WS750 WASTEWATER/STORMWATER SAMPLER
- RG600 TIPPING BUCKET RAIN GAUGE, 8 INCH
- RG700 4-20 mA Output Module
- RG200 RAIN GAUGE, 6 inch (TIPPING BUCKET)
- WE Sensor
- SP101 Solar Panel
- WE800 Weather Station
- SIT65 SATELLITE INTERNET TELEMETRY
- WIND ALARM CONTROLLER
- Expert MJK 1100-2100-3100
- 501 Electrode Control
- MJK 713 Open Channel Flowmeter