Extron Electronics DVS 605 User Guide User Manual
Page 58
Command
ASCII Command
(host to scaler)
Response
(scaler to host)
Additional Description
Video effect
Cut
E
0SWEF}
Swef0
]
Sets the switch to cut.
Dissolve
E
1SWEF
}
Swef1
]
Sets the switch to dissolve.
View setting
E
SWEF
}
0
]
(or 1
]
)
View setting (0 = cut, 1 = dissolve).
Effect duration
Set dissolve duration
E
X3%
EDUR}
EDURX3%
]
Sets the effect duration to tenths of seconds
(range 2 = 0.2 to 50 = 05.0 seconds. Default
is 3 = 0.3 seconds).
View duration
E
EDUR
}
X3%
]
View effect duration.
Front panel security lockout (Executive Mode)
Enable Executive
mode 1
1X
Exe1
]
Lock entire front panel.
Enable Executive
mode 2
2X
Exe2
]
Limited front panel adjustments (input
selection, PIP/Swap, and Auto- Image) can
be made.
Disable Executive
mode
0X
Exe0
]
Unlock front panel controls. All front panel
adjustments can be made.
View Executive
mode status
X
0
]
(or) 1
]
(or) 2
]
View the current status:
0 = off [default]; 1 = on, complete;
2 = on, limited adjustments.
Overscan mode (applies only to SMPTE [NTSC, PAL, 480p, 576p, 720p, 1080i, 1080p] input rates)
Set value
E
X#
*X2*OSCN}
OscnX#*X2*]
Set input format
X#
to overscan mode
X2*
.
View status
E
X#
OSCN}
X2*]
Show overscan mode status for input
format
X#
.
HDCP notification (green screen/message)
Enable notification
E
N1HDCP}
HdcpN1]
Enable the HDCP notification.
Disable notification
E
N0HDCP}
HdcpN0]
Disable the HDCP notification; instead
mute output.
Query notification
E
NHDCP}
X(]
Query the HDCP notification.
HDCP status (valid for HDMI inputs and HDMI oututs only)
Query input
E
IX!HDCP}
X3#]
HdcpIX!*X3#]
Query the HDCP status of the current input
X!
.
Verbose mode response
Query output
E
OX@HDCP}
X3#]
HdcpOX@*X3#]
Query the HDCP status of the HDMI output
X@
.
Verbose mode response
NOTE:
X! = Input selection: 1 to 5
X@ = Output selection: 0 = all outputs (default), 1 = analog (VGA, YUVp, HDTV), 2 = HDMI, 3 = 3G/HD-SDI, 4 = none
X# = Input video format: 0 = no signal detected, 1 = RGB, 2 = YUV auto, 3 = RGBcvS, 4 = S-video, 5 = composite,
6 = DVI/HDMI (only available for inputs 3, 4, and 5), 7 = Autodetect (default for inputs 1 and 2)
X( = Enable/disable: 0 = off/disable, 1 = on/enable
X2* = Overscan (applied to SMPTE [NTSC/PAL - 480p -1080p] input rates), 0 = 0.0% (default for RGB/HDMI),
1 = 2.5% (default for YUV, RGBcvS, S-video composite).
X3# = HDCP status (valid only on HDMI/DVI outputs): 0 = no sink or source detected, 1 = sink or source detected with HDCP,
2 = sink or source detected but no HDCP is present
X3% = Effect duration: from 2 to 50, in 0.1 second steps (where 2 = 0.2 seconds, 50 = 5.0 seconds), default = 3 (0.3 seconds)
DVS 605 • SIS Communication and Control
52