Hoyles General purpose button with LEDs and Buzzer User Manual

Installation instructions, Hoyles electronic developments ltd, Single gang buttons with integral buzzer and leds

Advertising
background image

Installation Instructions

Single gang buttons with integral buzzer and LEDs

This instruction covers the following products:
S1703PR Button with red LED, integral buzzer and engineer changeable label
S1705PR Button with red LED, integral buzzer and fixed CALL label
S1708PR Button with red LED, integral buzzer and fixed RESET label
All are available with Green. Blue or Yellow LEDs. eg. S1703PB These items are supplied with a back box for surface mounting but equally
they can be fitted to standard single gang electrical socket boxes for low profile mounting
NOTE:
The LEDs are current limited for 12 vdc operation. 24vdc version are available to special order eg S1703PY/24
The button contacts are rated at 50ma 24vdc resistive, N.O. press to close They should NOT be used for switch feeds to door strikes or
mag locks etc.. Consider the S1760 version for higher current applications.

BZ1

BZ1

87.0

18.0

18.0

8

7

.0

The S1703 is supplied un-labelled. The decal (included) has a clear window 10mm x 46mm. The area under the decal is 12mm wide to take
standard labelling machine tape. The window is free from adhesive, nevertheless, it is wise to maintain cleanliness and avoid fingerprints on the
inside of the window. If a labelling machine is not available a paper label can be used and examples are given below complete with cutting and
folding lines. If the text you require is not shown here then it is a fairly simple matter to make one with a word processing or graphics programme.
The dimensions here are given to help you. For a small extra charge the S1703 can be factory labelled to your requirements (subject to a
character limit)

65.0

49.0

1

2

.0

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

F

o

ld

Extent of Clear Window

Text in this 10mm x 46mm area

PRESS TO ENTER

PRESS TO START

PRESS TO EXIT

PRESS TO OPEN

Press for Assistance

EMERGENCY CALL

PRESS TO STOP

PRESS TO CLOSE

Press in Emergency

Press to Acknowledge

PRESS TO SET

Press to SILENCE

PRESS TO CLEAR

PRESS FOR ALARM

EMERGENCY

ACKNOWLEDGE

PRESS FOR ALARM

TE

XT

Fo

ld

NOTE:
The pushbutton will switch a
maximum of 50ma 24vdc
resistive. It is NOT suitable
for releasing door locks directly.

Before applying decal
fold paper label
and insert through slots

Ensure all surfaces are clean
and free from dust etc..

DWG: 60114.cdr iss1 Jan10

T. 01744 886600 F. 01744 886607 E. [email protected] W. www.hoyles.com

Hoyles Electronic Developments Ltd

L7

L8

R11

LED6

L

E

D

6

L

E

D

5

B

W Y

NC

NC

L5

L6

NO

COM

B

W Y

COM

NO

LED5

+

+12vdc

R8

ZD1

R

8

ZD1
on 24v
version
only

R

1

1

PB1

PB1

L1

L1

P2

P2

P1

P1

BZ

BZ

Advertising
Table of contents