6 setting the pressure of the feed rolls – Kemppi RA User Manual
Page 15
EN
4.6 setting the pressure of the feed rolls
To ensure the filler wire runs smoothly into the welding gun wire liner you should adjust the
pressure of the feed rolls of the wire drive mechanism.
Turn the orange coloured pressure adjustment knob(s) in a clockwise direction to increase the
pressure applied to the welding filler wire, and anticlockwise to decrease it.
NOTE!
Periodically remove and clean the short wire spiral located at the back of the wire feed
mechanism. See item D.
There is a graduation scale marked on the pressure arm above or below the orange
adjustment knob, depending on the Kempact RA used. For models fitted with the two roll
GT02 wire drive system, the more pressure applied, the greater the number of graduation
marks visible. For models fitted with the four roll DuraTorque wire drive system, the more
pressure applied, the fewer number of graduation marks visible.
for hard steel and stainless steel filler wires make sure there is sufficient pressure applied,
so avoiding filler wire slippage in the feed rolls.
NOTE!
Too much wire feed roll pressure may flatten the filler wire, damage its coating, increase
friction and result in the filler wire sticking in the welding gun liner or contact tip. Also excessive
pressure will result in increased wear to wire drive roll bearings, reducing their life.
13
© Kemppi Oy / 1336
- FastCool 10
- ArcFeed 300P
- KempCool 10
- KempCool 40
- KempactCool 10
- Procool 10
- Procool 30
- KMS 500
- KM 500
- MSF 57
- MF 33
- MF 29
- KMS 400 MVU
- FastMig Pulse 450
- MXF 67
- GT02SW
- FastMig MS 300
- FastMig MS 300
- SF 54
- KMS 400 AS
- KM 400 MVU
- MXP 38
- FastMig X 450
- FastMig 520
- MR 300
- M 420MV
- AS
- Evo 300
- Evo 300
- Pulse 2800
- Pulse 2800
- Pulse 3000 MVU
- MIG 2520
- MIG 2530
- DT 400
- ARC800
- Pulse TCS
- KempArc DT400
- Kempomat 2100
- Kempomat 4200
- Promig 100
- ProMXE Automotive panel
- ProMXE Automotive panel
- Pro Evolution 4200
- Promig 300
- Protig 410
- Protig 511
- Protig 511
- Promig 200 ML
- MagTrac F 61
- MLS 2000
- Master MLS MEX panel
- Mastercool 10
- 2200 Master
- Mastercool 12
- MasterTig MLS 4000
- 5001 Master
- 5000 Master
- Master S 500
- LT 250
- DC 2000
- DC 3500W
- MLS 2300 ACDC
- Evo 180
- Evo 180
- MLS 3000 ACDC VRD
- Evo 200
- 200MLP
- Adaptive 180
- Adaptive 150
- Adaptive 170
- MinarcTig 180
- MinarcTig 180MLP
- Minarc 140
- Minarc 151
- Minarc 150 VRD
- Minarc 150AU
- Minarc 120 AU
- Minarc 220
- MMT 42C
- TT-KTIG torches
- TT-KTIG torches
- Kempomig 4000WR
- Feed 120R
- Promig 120R
- Promig 540R