Exmark Metro 26 EN User Manual
Page 17
- 12 -
2. Open the fuel valve. The fuel valve is located at the lower left edge of the fuel
tank. Rotate the valve counter-clockwise to turn on fuel. (Fig. 9)
3. Move the throttle-choke control to the
(Choke) position.
NOTE: Do not use the choke when the engine is warm.
4. Pull the starter handle lightly until you feel resistance, then pull it sharply.
Allow the rope to return slowly.
5. When the engine starts, move the throttle control to the Fast position, and set
the ground speed control as desired.
NOTE: If the engine fails to start after 3 pulls, repeat steps 3-6.
4.3.3 Stopping the Engine:
Release the blade control bail. The blade should stop within 3 seconds. Move the
throttle to the (Off) position to kill the engine.
NOTE: If the blade does not stop within 3 seconds after releasing the blade
control bail, contact an Authorized Service Dealer.
4.3.4 Using the Self-Propel Drive:
The lawn mower has three ground speeds. 1 is slow, 2 is medium, and 3 is fast
(See Figure 6 for speed control lever location).
1.
Start
the
engine.
2. Using the ground speed control, select the desired ground speed.
3. Squeeze the drive bail against the handle (See Figure 5).
NOTE: Do not shift speeds while squeezing the ground speed control against
the handle. This can damage the transmission. Release the ground speed
control before changing speeds.
NOTE: You can vary the ground speed by increasing or decreasing the
distance between the ground speed control and the handle. Lower the control
bar to decrease the ground speed when you are making a turn or if the lawn
mower is moving too fast for you. If you lower the control bar too far the lawn
mower stops self-propelling. Squeeze the ground speed control closer to the
handle to increase the ground speed. When you hold the ground speed control
tight against the handle, the lawn mower self-propels at the maximum ground
FIGURE 8
FIGURE 9
- Lazer Z XS lXs29lKa725
- E-Series
- Pioneer S-Series Lawn Mower PNS20KA443
- Ultra VAC LAZER AS
- Ultra Vac 4500-420
- FMD604
- Quest Bagger 000 & higher
- Mhp3615ka
- Lazer ZCT
- Lazer ZXP
- METRO 21 MPKA21
- Vh4815ka
- Commercial 21 4500-686 Rev. B
- Turf Tracer S-Series TTS18KA523
- lazer Z E-Series 0
- FontRunner FR27
- NAV27KC
- Metro 21
- Metro 26
- Navigator 4500-368
- LAZER Z D-SERIES Mower 0
- Quest Lawn Mower
- Turf Tracer TT23KCC
- Vantage VT691KA524CA
- Lazer Z 4500-485
- Frontrunner
- Lawn Tractor
- Pioneer S-Series 312
- Standon 4500-436
- Lawn mower COMMERCIAL 21
- TT4817KA
- Turf Tracer S-Series 312
- LAZER Z 4500-484
- Mhp4815kac
- Phazer PHZ19KA343CA
- OCD01
- Lazer Z CT
- Lazer Z Mower 4500-507
- Turf Tracer HP 4500-358
- Vikingtm Hydro 4500-355
- LAZER Z 4500-471
- Lazer Z Advantage Series X
- Frontrunner 4500-497
- lazer Z 000 & Higher
- Lazer Z HP 505
- Turf Tracer x-series LP FMD604
- NAVIGATOR 4500-367
- Mower Pioneer E-Series 4500-996 Rev A
- Lazer Z 4500-872
- LAZER ZTM
- Quest Bagger 4500-438 rev. a
- Metro 21 Series
- FR20KC
- Lazer Z SX Diesel Models 4500-501 Rev A
- LZ27KC604
- Viking VH15KA483 ECS 15
- Lazer Z HP 465
- Commercial 21 000 & higher
- Metro 4500-353
- Navigator 850
- M217bsp
- OCD02
- Lazer ZHP
- Quest 4500-451
- Lazer Z XS
- Ultra Vac QDS 850
- FrontRunner Air-Cooled
- VH15KA362
- Cd48cd
- Standon 4500-435
- Lazer Z Advantage Series
- Turf Tracer HP 4500-359
- Lazer Z Mower 4500-645
- 4500-371
- TT23KAEP
- Quest 4500-450
- NAV20KC
- Phazer 4500-461
- Ultra Vac Lazer Z AS
- Ultra Vac 4500-421
- FR604
- Self Propelled Mower
- Frontrunner 4500-341
- Phazer 820
- Lazer Z D-Series 000 & higher
- Turf Tracer HP 4500-540 Rev. B
- FMD524
- Turf Tracer 4500-528
- M216KASPC
- 4500-370
- FrontRunner Diesel
- TR23KC
- Lazer Z XP
- Lazer XS 4500-380
- Phazer
- Turf Tracer TT23KAE
- FR524
- M216KASP
- Quest Bagger
- Ultra Vac
- Lazer Z
- QUEST 4500-339
- LAZER Z 103-0656
- Advantage Series 4500-466
- FMD 604
- Pioneer S-Series 000 & Higher
- Lazer Z DS-Series LZDS
- Lazer HP
- Metro 4500-352
- Lazer Z Advantage Series Models 850
- Metro
- Lazer Z S-Series