Lynx Professional Grills 42" Free Standing Grill L42PSR-1 - Manual (Page 35)

35
Pull off the control knob.
While holding the valve
shaft with pliers, insert a
While holding the valve While holding the valve
thin flat-blade screwdriver
shaft with pliers, insert a shaft with pliers, insert a
into the shaft and, while
watching the flame, adjust
it to a minimum stable
setting.
brAss burner flAMe/
Air flow AdjusTMenT
The amount of air that enters
a burner is controlled by the
air shutter .
Each grill burner is tested and
adjusted at the factory prior to
Each grill burner is tested and Each grill burner is tested and
shipment.
adjusted at the factory prior to adjusted at the factory prior to
however, fluctua-
adjusted at the factory prior to adjusted at the factory prior to
tions in gas pressure, gas con-
version and even in the quality
tions in gas pressure, gas con tions in gas pressure, gas con
of the gas itself may make it
version and even in the quality version and even in the quality
necessary to adjust the burner.
The flames of the main brass
burners should be visually
checked
stable with slight yellow tips.
The bright-blue core should
stable with slight yellow tips. stable with slight yellow tips.
►
►
ting burner adjustment. ting burner adjustment.
be about 3/8 inch high with a
total flame height of about 1
be about 3/8 inch high with a be about 3/8 inch high with a
1/2 inches.
The flames should burn
quietly. (no “torch” sounds)
and they should not “lift” up
quietly. (no “torch” sounds) quietly. (no “torch” sounds)
from the burner.
and they should not “lift” up and they should not “lift” up
if your flames do not match
those indicated in the photo,
ensure that the air shutter and
those indicated in the photo, those indicated in the photo,
burner ports are free and clear
of dirt, debris, or spider webs.
burner ports are free and clear burner ports are free and clear
If clear, then adjust the air
of dirt, debris, or spider webs. of dirt, debris, or spider webs.
shutter.
It is locked in place by a screw
which must be loosened
It is locked in place by a screw It is locked in place by a screw
before adjusting. once
adjusted retighten the screw.
to tt adjust:
Remove the racks and
briquette trays.
Lift out the burner, loosen
the set screw and then put
the burner back in place
the set screw and then put the set screw and then put
and light it.
the burner back in place the burner back in place
if the flame is excessively
yellow, indicating insuf
f the flame is excessively f the flame is excessively
-
ficient air
yellow, indicating insuf yellow, indicating insuf
, CA ficient air ficient air refully turn refully refully
the air shutter counter- the air shutter counter the air shutter counter
clockwise to allow more air
to the burner.
►
►
►
danger! danger!
Be extremely careful Be extremely careful
around hot around hot B Burners urners
and other grill parts. and other grill parts.
if the flame is noisy (sounds
like a torch) and tends to
lift away from the burner,
indicating too much
air, turn the air shutter
clockwise.
After the burner cools
down, remove it, tighten
the air shutter set screw
and reinstall the burner,
briquette trays and grill
racks.
briquette trays and grill briquette trays and grill
one lAsT Thing:
finally, before leaving, check
all the burners for proper
inally, before leaving, check inally, before leaving, check
operation. make sure the
all the burners for proper all the burners for proper
control knobs turn freely and
operation. operation.
completely through their full
control knobs turn freely and control knobs turn freely and
range.
ImPortant: ortant ortant
make sure the owner knows
where the main gas supply
shut off valve is located.
where the main gas supply where the main gas supply
finally, for safety and for
proper use & care, you
must leave this manual with
the owner. the owner the owner make sure you
advise them to keep it for
ake sure you ake sure you
future reference.
for technical assistance call:
lynx
ll technical tt support
888-289-5969
►
►