GE Industrial Solutions AF-300 G11 - Manual (Page 56)

5-3
Data subject to change without notice 7/07. © 2007 GE Drives
Func. Factory Setting Data Change
No. Setting Range Unit Min. 30 HP 40 HP Format during op
C20 JOG frequency C20 JOG Hz 0.00 to 400.00 Hz Hz 0.01 5.00 5 Y
C21 PATTERN (mode select) C21 PATTERN 0,1,2 - - 0 1
operation
C22 (Stage 1) C22 STAGE 1 Operation time: 0.00 to 6000 s s 0.01 0.00 F1 13
C23 (Stage 2) C23 STAGE 2 F1 to F4 and R1 to R4 0.00 F1 13
C24 (Stage 3) C24 STAGE 3 0.00 F1 13
C25 (Stage 4) C25 STAGE 4 0.00 F1 13
C26 (Stage 5) C26 STAGE 5 0.00 F1 13
C27 (Stage 6) C27 STAGE 6 0.00 F1 13
C28 (Stage 7) C28 STAGE 7 0.00 F1 13
C30 Frequency command 2 C30 FREQ CMD 2 0 to 11 - - 2 1 N
C31 Offset adjust (terminal [12]) C31 BIAS 12 -100.0 to +100.0% % 0.1 0.0 4 Y
C32 (terminal [C1]) C32 GAIN 12 0.0 to +200.0% % 0.1 100.0 3 Y
5-31 C33 Analog setting signal filter C33 REF FILTER 0.00 to 5.00s s 0.01 0.05 5 Y
P:Motor Parameters
P01 Number of motor 1 poles P01 M1 POLES 2 to 14 - 2 4 9 N
P02 Motor 1 (capacity) P02 M1-CAP Up to 30 HP: 0.01 to 60 HP Hp 0.01 motor capacity 5
40 HP and above: 0.01 to 600 HP
P03 (rated current) P03 M1-Ir 0.00 to 2000 A A 0.01 motor rated current 19 N
P04 (tuning) P04 M1 TUN1 0, 1, 2 - - 0 21 N
P05 (on-line tuning) P05 M1 TUN2 0, 1 - - 0 1 N
P06 (no-load current) P06 M1-Io 0.00 to 2000 A A 0.01 standard rated value 19 N
P07 (%R1 setting) P07 M1-%R1 0.00 to 50.00% % 0.01 standard rated value 5 Y
P08 (%X setting) P08 M1-%X 0.00 to 50.00% % 0.01 standard rated value 5 Y
P09 Slip compensation control P09 SLIP COMP1 0.00 to 15.00 Hz Hz 0.01 0.00 5 Y
H:High Performance Functions
H03 Data initializing H03 DATA INIT 0, 1 - - 0 1 N
H04 Auto-reset (times) H04 AUTO-RESET 0, 1 to 10 times - 1 0 1 Y
H05 (reset interval) H05 RESET INT 2 to 20 s s 1 5 1 Y
H06 Fan stop operation H06 FAN STOP 0, 1 - - 0 1 Y
H07 ACC/DEC pattern (mode select) H07 ACC PTN 0,1,2,3 - - 0 1 N
H08 Rev. phase sequence lock H08 REV LOCK 0, 1 - - 0 1 N
H09 Start mode H09 START MODE 0, 1, 2 - -- 0 1 N
H10 Energy-saving operation H10 ENERGY SAV 0, 1 - - 0 1 Y
H11 DEC mode H11 DEC MODE 0, 1 - - 0 1 Y
H12 Instantaneous OC limiting H12 INST CL 0, 1 - - 1 1 N
H13 Auto-restart (restart time) H13 RESTART t 0.1 to 10.0 s s 0.1 0.1 0.5 3 N
H14 (freq. fall rate) H14 FALL RATE 0.00 to 100.00 Hz/s Hz/s 0.01 10.00 5
H15 (holding DC voltage) H15 HOLD V 3-phase, 230V class: 200 to 300V V 1 200V class: 235V 1
3-phase, 460V class: 400 to 600V 400V class: 470V
H16 (OPR command self hold time) H16 SELFHOLD t 0.0 to 30.0 s, 999 s 0.1 999 3
H18 Torque control H18 TRQ CTRL 0, 1, 2 - - 0 1
H19 Active drive H19 AUT RED 0, 1 - - 0 1 Y
H20 PID control (mode select) H20 PID MODE 0, 1, 2 -- - 0 1 N
5-38 H21 (feedback signal) H21 FB SIGNAL 0, 1, 2, 3 - - 1 1 N
H22 (P-gain) H22 P-GAIN 0.01 to 10.00 times - 0.01 0.1 5 Y
H23 (I-gain) H23 I-GAIN 0.0, 0.1 to 3600 s s 0.1 0.0 3 Y
H24 (D-gain) H24 D-GAIN 0.00 s , 0.01 to 10.0 s s 0.01 0.00 5 Y
H25 (feedback filter) H25 FB FILTER 0.0 to 60.0 s s 0.1 0.5 3 Y
H26 PTC thermistor (mode select) H26 PTC MODE 0, 1 0 1 Y
H27 (level) H27 PTC LEVEL 0.00 to 5.00V V 0.01 1.60 5 Y
H28 Droop operation H28 DROOP 9.9 to 0.0 Hz Hz 0.1 0.0 4 Y
H30 Serial link (function select) H30 LINK FUNC 0, 1, 2, 3 - - 0 1 Y
H31 Modbus-RTU (address) H31 ADDRESS 0 (broadcast), 1 to 247 - 1 1 1 N
H32 (mode select on no response error) H32 MODE ON ER 0, 1, 2, 3 - - 0 1 Y
H33 (timer) H33 TIMER 0.0 to 60.0 s s - 2.0 3 Y
H34 (baud rate) H34 BAUD RATE 0, 1, 2, 3 - - 1 1 Y
H35 (data length) H35 LENGTH 0 (8-bit fixed) - - 0 1 Y
H36 (parity check) H36 PARITY 0, 1, 2 - - 0 1 Y
H37 (stop bits) H37 STOP BITS 0 (2-bit), 1(1-bit) - - 0 1 Y
H38 (no response error detection time) H38 NO RES t 0 (no detection), 1 to 60 s s 1 0 1 Y
H39 (response interval) H39 INTERVAL 0.00 to 1.00 s s 0.01 0.01 5 Y
5-42
5-43
5-37
5-39/40
5-41
5-36
Pg.
5-29
5-29/30
5-30
5-32
5-33
5-34
5-35
Y
N
Y
Name LCD Display
N
N