Foredom C.SCH-1 - Manual

Parts List
C.SCT−1 & C.SCH−1
Foot Control, 115V
FOREDOM
The Foredom Electric Company
16 Stony Hill Rd., Bethel, CT 06801 • 203−792−8622
Fax: 203−796−7861 • www.foredom.net
}
Wiring Diagram
FORM DN 12/10
Qty Description Part No. Item
1 Cover CP10691 1
1 Trigger Switch, 125V CP10857 2
2 Screw, 6−32 x 5/16" CP10571 3
1 Bracket CP11030 4
1 Base CP10690 5
1 Base Pad CP10753 6
1 Specification Label SCT−1.LAB 7
1 Male Cordset CP10541 8
2 Hinge Pin CP10584C 9
1 Grommet CP10578 10
1 Terminal Ring CP10580 11
1 Lock Washer, #8 CP10564 12
1 Screw, 8−32 x 1/4" CP10563 13
1 Female Cordset (SCT−1)
Female Cordset (SCH−1) CP10542
CP10830 14
1 2 Wire Connector CP11029 15
1 Set Screw CP10562 16
1 Spring CP10588 17
Disconnect Foot Control from Motor and Wall Outlet.
Instructions for Removing
and Replacing Trigger Switch
With a punch and hammer drive two Pins (9) in until Cover (1)
lifts from each side of Base (5).
Remove two Screws (3) from Bracket (4). After the wires have
been removed from the switch, as instructed in paragraph 4,
remove the switch from the board, insert the new switch in its
place, and follow the instructions in paragraph 5 and 6.
Remove Cover and drive Pins outward with hammer and punch
to remove.
On older Switches, all the terminals will be push-in, spring clamp
type. On newer Switches, Terminal 1 has a screw for fastening
the wire lead. To remove wires from the push-in terminals, insert
1.3mm [.05in] approximate diameter pin or the blade of a jeweler's
screwdriver all the way into the terminal socket to release the spring
clamp. Grasp the tool and wire and pull them together out of the
socket. If you have difficulty removing the wires from the push-in
terminals and you have wire-cutting, stripping, and soldering tools,
you can cut the wires off where they exit from the terminals. To
prepare the cut wires for installation into the replacement Switch,
strip them back exactly 8.25 mm [5/16 in], then apply solder to the
stripped ends to fuse the strands together.
Insert new Trigger Switch into Bracket.
4.
3.
2.
7.
Install Cover over Spring (17) and align holes to Base.
Insert Pins (9) and seat them with hammer.
Position wires around post of Base so wires will not
interfere with Cover travel.
Install Bracket and Switch into Base using two Screws (3).
8.
9.
1.
5.
Connect Wires to New Trigger Switch as shown in the
Wiring Diagram. Push wires all the way in, so that no bare wire
is exposed. On Screw Terminal 1, push the wire lead all the way
into the socket then tighten the screw firmly. Push the other
wire lead all the way into terminal 6. Pull on all the wires, making
sure they are secure.
6.
Bracket
Trigger Switch
5
6
1
4
3
2
Attach Ground
Screw to Base
BLK
WHT
GRN
GRN
WHT
BLK
Female Receptacle
to Motor
Male Plug to
AC Power Source
1
3
4
5
6
7
8
9
10
15
16
17
14
11
12
13
2
Wire
Connector