KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.2.01 to 2.37 - Manual (Page 147)

BOP-1K 022108
B-1
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 INTRODUCTION
This appendix defines the SCPI subsystem commands and queries used with the BOP power sup-
ply. Subsystem commands are defined in PAR. B.3 through B.120, arranged in groups as they
appear in the tree diagram, Figure 3-18. Table B-1 provides a quick reference of all SCPI sub-
system commands and queries used in the BOP.
TABLE B-1. SCPI SUBSYSTEM COMMAND/QUERY INDEX
COMMAND PAR. COMMAND PAR.
ABOR B.3 [SOUR:]CURR:PROT:MODE, ? B.53, B.54
CAL B.4 [SOUR:]CURR:PROT:NEG, ? B.55, B.56
INIT[:IMM] B.5 [SOUR:]CURR:PROT:POS, ? B.57, B.58
INIT:CONT, ? B.6, B.7 [SOUR:]CURR:PROT:LIM[:BOTH], ? B.59, B.60
MEAS:CURR? B.8 [SOUR:]CURR:PROT:LIM:NEG, ? B.61, B.62
MEAS:VOLT? B.9 [SOUR:]CURR:PROT:LIM:POS, ? B.63, B.64
MEM:REL B.10 [SOUR:]CURR:TRIG, ? B.65, B.66
MEM:UPD B.11 [SOUR:]VOLT B.67, B.68
OUTP[:STAT], ? B.12, B.13 [SOUR:]VOLT:LIM[:BOTH], ? B.69, B.70
OUTP:MODE, ? B.14, B.15 [SOUR:]VOLT:LIM:NEG, ? B.71, B.72
[SOUR:]FUNC:MODE, ? B.16, B.17 [SOUR:]VOLT:LIM:POS, ? B.73, B.74
[SOUR:]FUNC:MODE:TRIG, ? B.18, B.19 [SOUR:]VOLT:MODE, ? B.75, B.76
[SOUR:]LIST:CLE B.20 [SOUR:]VOLT:PROT[:BOTH], ? B.77, B.78
[SOUR:]LIST:COUN, ? B.21, B.22 [SOUR:]VOLT:PROT:MODE, ? B.79, B.80
[SOUR:]LIST:CURR, ? B.23, B.24 [SOUR:]VOLT:PROT:NEG, ? B.81, B.82
[SOUR:]LIST:CURR:APPL B.25 [SOUR:]VOLT:PROT:POS, ? B.83, B.84
[SOUR:]LIST:CURR:SWE, ? B.26, B.27 [SOUR:]VOLT:PROT:LIM[:BOTH], ? B.85, B.86
[SOUR:]LIST:POIN? B.28 [SOUR:]VOLT:PROT:LIM:NEG, ? B.87, B.88
[SOUR:]LIST:DWEL, ? B.29, B.30 [SOUR:]VOLT:PROT:LIM:POS, ? B.89, B.90
[SOUR:]LIST:DWEL:POIN? B.31 [SOUR:]VOLT:TRIG B.91, B.92
[SOUR:]LIST:QUER, ? B.32, B.33 STAT:OPER:COND? B.93
[SOUR:]LIST:RES? B.34 STAT:OPER:ENAB, ? B.94, B.95
[SOUR:]LIST:VOLT, ? B.35, B.36 STAT:OPER[:EVEN]? B.96
[SOUR:]LIST:VOLT:APPL B.37 STAT:PRES B.97
[SOUR:]LIST:VOLT:SWE, ? B.38, B.39 STAT:QUES[:EVEN]? B.98
[SOUR:]LIST:VOLT:POIN? B.40 STAT:QUES:COND? B.99
[SOUR:]CURR, ? B.41, B.42 STAT:QUES:ENAB, ? B.100, B.101
[SOUR:]CURR:LIM[:BOTH], ? B.43, B.44 SYST:COMM:GPIB:ADDR, ? B.102, B.103
[SOUR:]CURR:LIM:NEG, ? B.45, B.46 SYST:ERR? B.104
[SOUR:]CURR:LIM:POS, ? B.47, B.48 SYST:ERR:CODE? B.105, B.106
[SOUR:]CURR:MODE, ? B.49, B.50 SYST:KEYB, ? B.107, B.108
[SOUR:]CURR:PROT[:BOTH], ? B.51, B.52 SYST:PASS:CEN B.109
NOTE: Commands listed above that are followed by “, ?“ have a related query.