KEPCO BOP 1KW-MG Operator Manual, Firmware Ver.2.01 to 2.37 - Manual (Page 17)

BOP-1K 022108
ix
LIST OF TABLES
TABLE TITLE PAGE
1-1 BOP 1000 Watt Model Parameters .............................................................................................................1-1
1-2 BOP General Specifications .......................................................................................................................1-2
1-3 Equipment Supplied ....................................................................................................................................1-15
1-4 Safety Symbols ...........................................................................................................................................1-15
1-5 Accessories .................................................................................................................................................1-16
2-1 Rear Panel Connector Functions ................................................................................................................2-2
2-2 IEEE 1118 Connector Input/Output Pin Assignments .................................................................................2-3
2-3 Trigger Port Pin Assignments .....................................................................................................................2-3
2-4 External Protection Connector Input/Output Pin Assignments ....................................................................2-3
2-5 RS232C PORT Input/Output Pin Assignments ...........................................................................................2-4
2-6 Parallel/Serial Control Out Port Pin Assignments .......................................................................................2-4
2-7 Parallel/Serial Control In Port Pin Assignments ..........................................................................................2-4
2-8 Parallel/Serial Protect In Port Pin Assignments ..........................................................................................2-5
2-9 Parallel/Serial Protect Out Port Pin Assignments .......................................................................................2-5
2-10 Analog I/O Port Input/Output Pin Assignments ...........................................................................................2-6
2-11 IEEE 488 Port Input/Output Pin Assignments .............................................................................................2-7
2-12 Multiple Units Menu Functions ....................................................................................................................2-19
2-13 Slave Status Message Definitions ..............................................................................................................2-21
3-1
Front Panel Controls and Indicators ...........................................................................................................3-2
3-2 Special Key Functions ................................................................................................................................3-3
3-3 Display (Operator Convenience) Menu Functions ......................................................................................3-10
3-4 Voltage and Current Parameter Definitions ................................................................................................3-13
3-5 Max/Min Settings Menu ..............................................................................................................................3-16
3-6 Power Supply Behavior when Output is set to OFF ....................................................................................3-20
3-7 Examples Showing How Power-up Settings Function ................................................................................3-21
3-8 Save/recall menu ........................................................................................................................................3-23
3-9 Sine, Triangle and Ramp Waveform Frequency vs. Points ........................................................................3-26
3-10 Square Waveform Frequency vs. Points ....................................................................................................3-26
3-11 Waveform Segment Details Menu ..............................................................................................................3-28
3-12 New Waveform Settings Menu ...................................................................................................................3-30
3-13 Error Message Explanations .......................................................................................................................3-33
3-14 Revisions/test Menu ....................................................................................................................................3-37
3-15 Analog Remote Setup Menu .......................................................................................................................3-38
3-16 Interface Settings Menu ..............................................................................................................................3-44
3-17 Operation of #RST Command ....................................................................................................................3-45
3-18 IEEE 488 (GPIB) Bus Interface Functions ..................................................................................................3-46
3-19 IEEE 488 (GPIB) Bus Command Mode Messages .....................................................................................3-47
3-20 IEEE 488 (GPIB) Bus Data Mode Messages ..............................................................................................3-47
3-21 Rules Governing Shortform Keywords ........................................................................................................3-57
4-1
Calibration Summary ..................................................................................................................................4-1
4-2 Suggested Sense Resistors ........................................................................................................................4-3
4-3 Voltage Calibration Measurements and Tolerances ...................................................................................4-4
4-4 Current Calibration Measurements and Tolerances ...................................................................................4-5
4-5 Calibration Storage ....................................................................................................................................4-16
A-1 IEEE 488.2 Command/query Index ........................................................................................................... A-1
A-2 Standard Event Status Enable Register and Standard Event Status Register Bits ................................... A-1
A-3 Service Request Enable and Status Byte Register Bits ............................................................................. A-5
A-4 Built-in test Error Codes ............................................................................................................................. A-6
B-1 SCPI Subsystem Command/query Index .................................................................................................. B-1
B-2 List Data Table ........................................................................................................................................... B-6
B-3 Operation Condition Register, Operation Enable Register,
and Operation Event Register Bits .......................................................................................................... B-20
B-4 Questionable Event Register, Questionable Condition Register
and Questionable Condition Enable Register Bits .................................................................................. B-21
B-5 Error Messages .......................................................................................................................................... B-25