Paralleled dual fx system – Outback Power Systems VFX Series International Installation Manual User Manual
Page 27
Advertising
25
PARALLELED DUAL FX SYSTEM
• All AC wiring from the AC source and to the AC loads must collectively handle 60 amps AC or more.
• All other AC wiring capacity must equal 30 amps AC.
• A paralleled dual FX system can continuously power 4-6kW of loads depending on which model is
used.
Parallel/Dual System with Two FXs
NOTE: Program the lowest-installed FX as Master (1-2ph MASTER) and the second FX as an OutBack
L1 Slave (OB SLAVE L1). The Master FX must be plugged into Port 1 of the HUB.
(16.0 mm
2
)
Advertising
This manual is related to the following products:
See also other documents in the category Outback Power Systems Power suppliers:
- GS8048
- GTFX2524
- VFX 3524M
- FX2012MT
- Systems
- Sealed FX
- VFX Series
- Hitch DOM-OBK03
- GFX Series Inverter/Charger Installation Manual
- GFX Series Inverter/Charger Operators Manual
- GFX International Series Installation Manual
- GFX International Series Operators Manual
- GS8048 Installation Manual
- GS8048 Operator Manual
- GS Load Center Installation Manual
- GS Load Center Installation Manual
- Radian Series Inverter/Charger Service Instructions
- GS8048 Quick Start Guide
- GS7048E Installation Manual
- GS7048E Operators Manual
- GS7048E Quick Start Guide
- GS8048A Quick Start Guide with GSLC
- GS8048A Installation Manual
- GS8048A Operators Manual
- FX Series Installation Manual
- FX Series Programming Manual
- FX Series Circuit Board Replacement Instruction
- FX Series Export Inverter/Charger Programing Manual
- GTFX Series Inverter/Charger Programing Manual
- GTFX Series Inverter/Charger Programing Manual
- GTFX Series Inverter/Charger Installation Manual
- PV 8 Combiner
- FW-X240 Installation Manual
- PSX-240-Relay Installation Manual
- FLEXware 250 - Users Guide
- FW-IOB-S-120VAC Input/Output/Bypass Assembly - Installation Instructions
- FW-IOB-S-230VAC Input/Output/Bypass Assembly - Installation Instructions
- FLEXware ACA AC Conduit Adapter Users Guide
- FLEXware Mounting Plate Users Guide
- FLEXware 500 Users Guide
- FW-IOB-D-120VAC Input/Output/Bypass Assembly - Installation Instructions
- FW-IOB-D-120/240VAC Input/Output/Bypass Assembly - Installation Instructions
- FW-IOB-D-230VAC Input/Output/Bypass Assembly - Installation Instructions
- FLEXware MATE3 Mounting Bracket - Installation Instructions
- FLEXware 1000 Users Guide
- FW-IOB-Q-120VAC Input/Output/Bypass Assembly - Installation Instructions
- FW-IOB-Q-230VAC Input/Output/Bypass Assembly - Installation Instructions
- FW-IOB-Q-240VAC Input/Output/Bypass Assembly - Installation Instructions
- FW-IOB-T-120/208VAC Input/Output/Bypass Assembly - Installation Instructions
- FW-IOB-T-230/400VAC Input/Output/Bypass Assembly - Installation Instructions
- HUB-4 System Communication Manager User’s Manual
- MATE System Controller and Display Installation and User Manual
- MATE3 USB Card Owner’s Manual
- FLEXnet DC Users Guide
- FLEXpower TWO Quick Start Guide
- MATE3 Owners Manual
- PV Ground-Fault Detector Interrupter (GFDI) Installation
- FLEXpower ONE System Overview
- FLEXpower ONE Quick Start Guide
- FLEXpower ONE One Fully Pre-Wired Single Inverter System Installation Manual
- FLEXmax 60 Owners Manual
- FLEXmax 60 Quick Start Guide
- FLEXmax 60 Quick Start Guide
- FLEXmax Extreme Owners Manual
- FLEXmax Extreme Quick Start Guide
- FLEXmax Extreme AXS Card Manual
- MATE Serial Communications Guide
- MATE2M System Controller and Display Installation and User Manual
- HUB10.3 - Quick Start Guide
- AXS Port SunSpec Modbus Interface Owners Manual
- IBR-3 Installation Manual
- OBE 1 & 2 Quick Start Guide
- EnergyCell RE Battery Owners Manual