Nikon COOLSHOT - Manual (Page 55)

108 109
Se
En
Jp
Fr
Es
Pt
Ru
Nl
De
It
Dk
Pl
Hu
Cz
Fi
No
Ro
Se
En
Jp
Fr
Es
Pt
Ru
Nl
De
It
Dk
Pl
Hu
Cz
Fi
No
Ro
Sammanfattning av användning
Användning av reglage, justeringar eller
funktioner för andra ändamål än de avsedda kan
leda till exponering av farlig strålning.
1. Sätt i ett batteri i batterifacket. (Se "Byta
Batteri")
2. Dioptrijustering
Justera dioptrin för att få en tydlig bild på LCD-
skärmen.
Vrid först dioptrijusteringsringen moturs tills
den stoppar. Slå sedan på strömmen för att
aktivera LCD-skärmen när du tittar genom Nikon
laseravståndsmätare. Rotera dioptrijusteringsringen
medurs tills skärmen är fokuserad.
Om dioptrin inte justeras efter din syn kan du få
svårt att korrekt fokusera på dina mål.
3. Mätning
Kontrollera vilken enhet som är inställd innan du
mäter. Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target .
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target .
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target .
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target .
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target .
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target .
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target .
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts.
1. Tryck på POWER-knappen
för att slå på strömmen. 2. Sikta mot målet.
Direkt efter att
strömmen slås på.
(Initierar)
Viloläge Insiktning
3. Tryck på POWER-knappen en gång för att starta kontinuerlig
mätning i 8 sekunder. (Det går inte att göra enskilda mätningar med
den här modellen.)
Mätning
4. Den interna displayen visar "distance" (Avstånd) eller "fail to measure"
(Misslyckad mätning) i 8 sekunder. Laserstrålningsmärket blinkar
under mätningen.)
Misslyckad mätning
eller kunde inte mäta
avstånd.
Visar den
uppmätta figuren.
(Mål 1)
Visar den uppmätta
figuren. (Mål 2)
Measurement
1. Press the POWER button for power-on.
(Power turns off 8 seconds after the last
operation.)
Immediately after power-on.
(Initializing)
Stand-by. Target focusing.
2. Aim at the target .
3. Press POWER button once to start
continuous measurement for 8 seconds.
(Single measurement mode is not
available with this laser rangefinder.)
Measuring.
4. For 8 seconds, the internal display shows “distance” and “fail to measure” indicator alternately.
(Laser irradiation mark is blinking.)
Failure to measure or
unable to measure distance.
Displays the measured
figure. (Target 1)
Displays the measured
figure. (Target 2)
5. After continuous measurement, the measured results are displayed for 8 seconds, then power
turns off.
If you press the POWER button during power-on (while the internal display is lit), another
8-second measurement starts. 5. Efter kontinuerlig mätning visar indikatorn mätresultaten,
sedan slås strömmen av. Om du trycker på POWER-knappen när
strömmen slås på (medan den interna skärmen är tänd), startar
en ny 8-sekundersmätning.
Vid t. ex. mätning av avståndet till en flagga på en golfbana uppnås
mätning enklare om flaggan skannas under mätning. Om det
inte finns några föremål mellan dig och flaggan, är det kortaste
resultatet avståndet till flaggan.
4. Välja visningsenhet (fabriksinställningen är yard)
1. Kontrollera att den interna LCD-skärmen är på.
2. Tryck in och håll MODE knappen (2 sekunder eller
längre).
3. När visningsenheten har ändrats, släpper du MODE
knappen.
4. När enheten har ställts in konverteras resultaten och
visas i vald mätenhet.
Meter [ ] Yard [ ]
6. Indikering för låg batteriladdning
Blinkande anger att batteriladdningen är
låg och att batteriet ska bytas. (Se "Byta batteri".)
7. Bakgrundsbelysning
Använd bakgrundsbelysningen för att se LCD-
panelen i mörka förhållanden.
Genom att trycka kort på MODE-knappen
(mindre än 2 sekunder) när strömmen är
på kan bakgrundsbelysningen stängas AV
eller PÅ. Bakgrundsbelysningen kan också
stängas av genom att vrida av strömmen till
laseravståndsmätaren. I detta fall kommer
bakgrundsbelysningen att vara avstängd när
strömmen till laseravståndsmätaren slås på igen.
5. Avståndsdisplay
COOLSHOT använder sig av Prioritesinställningssystem
för första målet.
Om man får olika resultat från en enskild mätning, visar
den avståndet till det närmaste målet på LCD-skärmen.
e.g.) Om man mäter ett träd som står frramför ett hus;
visas "115 m" (avstånd till trädet).
Detta är användbart när du golfar.
Träd Staket Hus
Avstånd till mål 115 m 123 m 128 m