Document Outline

• Enpac Ex Data Collector Users Guide
• Important User Information
• Table of Contents
• Introduction
  • Overview of Emonitor and the Enpac Ex
  • Using the Manual
    • Organization
    • Document Conventions
  • Using Online Help
    • Emonitor Online Help
    • Enpac Ex Online Help
  • Technical Support
• The Enpac Ex
  • Overview of the Enpac Ex
  • Certification and Operation
    • Cleaning
    • Avoid Water
    • Avoid Damage
    • Using the Enpac Ex in Hazardous Areas
  • Enpac Ex Diagram and Key Definitions
    • READ/OK Key
    • Arrow Keys
    • ON/OFF Key
    • +/- Key
    • Decimal Key
    • Numeric Keys
  • External Connectors
    • Signal Connector
    • Trigger Connector
    • Charger Connector
    • RS-232 Interface
  • LED Indicators
  • Enpac Ex Battery Pack
    • Checking Battery Life
    • Inserting/Removing the Battery Pack
  • Assembling the Strap
  • System Modes
  • Main Screens
    • Main Menu
    • Instrument Setup Screen
    • Data Collection Screen
    • Review Data Screen
    • Help Screen
  • Basic Enpac Ex Operations
    • Powering On and Off the Enpac Ex
    • Setting the Date, Time, and Date Format
    • Displaying the Operating System Version Number
    • Changing the Display Contrast
    • Rebooting the Enpac Ex
    • Hardware Reset
    • Calibrating the Touchscreen
    • Viewing Settings for Current Measurement Definition
    • Loading the Enpac Ex Operating System
• Setting Up Measurements
  • Measurement Definition Options
    • Measurement Types
    • Measurement Filters
    • Measurement Units
  • Setting Up Collection Specifications
    • Measurement Input Types
    • Measurement Window Types
    • Measurement Signal Detection Types
    • Measurement Maximum Frequencies
    • Measurement Resolution
    • Number and Type of Averages
  • Setting Up Measurement Definitions
    • Magnitude Measurement Definitions
    • Magnitude and Phase Measurements at Orders
    • Numeric (Process) Measurement Definitions
    • Spectrum Measurement Definitions
    • Time Waveform Measurement Definitions
    • Voltage Measurement Definitions
    • Combining Measurement Definitions for a Location
  • Setting Up Alarms, Lists, and Inspection Codes
    • Alarms and the Data Collector
    • Lists and the Data Collector
    • Inspection Codes and the Data Collector
• Loading and Unloading
  • Setting Up for Communication
    • Set Up the Current Data Collector
    • Set Up the Computer for Communication
    • Set Up the Data Collector for Communication
    • Connecting the Data Collector and Computer
  • Loading Lists to the Data Collector
    • Initializing the Data Collector before Loading
    • Loading Inspection Codes
    • Overriding the Collect On Alarm Setting
    • Selecting the List(s)
    • Loading Selected Lists to the Data Collector
    • Displaying the Data Collector Driver Version Number
  • Unloading Lists from the Data Collector
    • Unloading Lists in Emonitor
    • Unloading Unscheduled (Off Route) Data from the Enpac Ex
    • Unloading Measurements using Smart Unscheduled Mode
    • Automatically Printing Reports after Unloading
• Collecting and Reviewing Data
  • Preparing for Data Collection
    • Connecting the Transducer to the Data Collector
    • Selecting the Data Collection Options
  • Collecting Route Data
    • Selecting a Route
    • Starting Data Collection
    • Selecting Inspection Codes
    • Manually Entering a Numeric Measurement
    • Collecting a Process DC Voltage Measurement
    • Collecting a Magnitude Measurement
    • Collecting a Spectrum Measurement
    • Collecting a Time Waveform Measurement
    • Collecting Magnitude and Phase Measurements at Orders
    • Moving through a List
  • Collecting Off Route Data
    • Methods for Collecting Off Route Data
    • Collecting Off Route Data using a Pre-Defined Measurement
    • Creating and Collecting a User-Defined Point
    • Storing Unscheduled Data and Emonitor
  • Reviewing Data
    • Review Data Screen
    • Reviewing Overall Data
    • Reviewing Signature Data
  • Printing Enpac Ex Screens
    • Printing Screens with the Enpac Ex
    • Printing Reports and Plots Using Host Software
• Specifications
• Enpac Ex Parameters
  • Instrument Setup Parameters
  • Instrument Configuration Parameters
  • Offroute User Parameters
• Frequently Asked Questions and Answers
  • Setting Up Measurement Definitions in Emonitor
    • How do I set up measurement definitions?
    • Why do unsupported selections appear in Emonitor?
    • Why can’t I edit the measurement definitions units?
  • Loading Lists to the Enpac Ex
    • I think I lost some data. What happened?
    • Why won’t Emonitor load a list to the Enpac Ex?
    • Why does Emonitor rebuild the Quickload files?
    • How do I tell when loading or unloading is done?
  • Collecting Data with the Enpac Ex
    • Why does the Enpac Ex seem to skip measurements at a location?
    • Why won’t the Enpac Ex combine magnitude and phase or manual entry measurements at a location?
    • What do the USER (eus) and User (s) units mean?
    • Why are the alarms in the Enpac Ex not what I selected?
    • Why aren’t inspection codes available for a list?
    • How can I reduce the ranging time required during collection?
  • Unloading Data from the Enpac Ex
    • How do I unload data from more than one list?
    • How do I clear data from lists after unloading?
    • How do I print reports after unloading data?
  • Analyzing Data in Emonitor
    • Why does the magnitude reading not correspond to the calculated overall value?
• Glossary
• Index