MacDon M150 SP - Manual (Page 228)

M150 AND M200 CDM / WCM FAULT CODES
Form # 169017 / 169087 / 169095
226
Revision C
E 1 R A N G E N O T A L L O W E D HIGH range activated while in Cab forward (M150).
E 2 R T C N O T A L L O W E D Return To Cut activated with the header off.
E 3 S I G N A L S N O T A L L O W E D Turn Signals activated while in Cab forward.
E 4 H D R D R V N O T A L L O W E D Header engage switch activated while in Engine forward.
E 5 C H K H E A D E R I D 1 1 1 1 Indicates that the HEADER ID has changed while engaged - continuous tone
E 6 T E M P G A U G E S H O R T Wiring / connection problem.
E 7 S P E E D S T I C K S H O R T Wiring / connection problem.
E 8 H E A D E R E N A B L E S H O R T Wiring / connection problem.
E 9 W C M E N A B L E S H O R T Wiring / connection problem.
E 10 C D M I N T E R N A L E R R O R Internal hardware or software problem.
E 11 C D M P O W E R U P CDM Module did not power up correctly.
E 12 W C M P O W E R U P WCM Module did not power up correctly.
E 13 F U E L S O L E N O I D WCM Fuel solenoid output fault detected.
E 14 E114 D W A D R I V E P W M V 1 3 DWA Drive - PWM solenoid drive fault detected - short circuit / open circuit
E 15 E115 K N I F E D R I V E P W M V 8 Knife drive - PWM solenoid drive fault detected - short circuit / open circuit
E 16 E116 D R A P E R D R V P W M V 9 A Draper Drive - PWM solenoid drive fault detected - short circuit / open circuit
E 17 E117 R E E L D R I V E P W M V 9 B Reel Drive - PWM solenoid drive fault detected - short circuit / open circuit
E 18
E 19 E119
L O A D S E N S E V 1 6 Disc Block valve 16 - solenoid drive fault detected - short circuit / open circuit
E 20
E 21 E121
R E V E R S E R V 1 1 C Reverser - Solenoid V14 fault detected - short circuit / open circuit
E 22
E 23 E123
R E V E R S E R V 1 1 A / B / 1 2 Reverser - Solenoid V11A, 11B or 12 fault detected - short circuit / open circuit
E 24 E124 D E C K S H F T R I G H T V 1 4 Right Deck Shift solenoid V14 fault detected - short circuit / open circuit
E 25 E125 D E C K S H F T L E F T V 1 5 Left Deck Shift solenoid V15 fault detected - short circuit / open circuit
E 26 E126 D W A U P V 2 C 2 DWA Raise solenoid V2C2 fault detected - short circuit / open circuit
E 27 E127 D W A D O W N V 4 C 2 DWA Lower solenoid V4C2 fault detected - - short circuit / open circuit
E 28 E128 T I L T R E T R A C T V 2 B Tilt Retract solenoid V2B fault detected - short circuit / open circuit
E 29 E129 T I L T E X T E N D V 2 A Tilt Extend solenoid V2A fault detected - short circuit / open circuit
E 30 E130 4 W A Y V A L V E V 6 4 Way valve solenoid V6 fault detected - short circuit / open circuit
E 31 E131 B Y P A S S V A L V E V 1 Bypass valve solenoid V1 fault detected - short circuit / open circuit
E 32 E132 H E A D E R U P / D O W N V 4 A Header up / down solenoid V4A fault detected - short circuit / open circuit
E 33 E133 S C R E E N C L E A N E R S Screen cleaner output fault detected - short circuit / open circuit
E 34 E134 R I G H T S T O P L A M P Right stop lamp output fault detected - short circuit / open circuit
E 35 E135 L E F T S T O P L A M P Left stop lamp output fault detected - short circuit / open circuit
E 36 E136 R I G H T T U R N L A M P Right turn lamp output fault detected - short circuit / open circuit
E 37 E137 L E F T T U R N L A M P Left turn lamp output fault detected - short circuit / open circuit
E 38 E138 M A I N D R I V E V 1 0 Main header drive solenoid V10 fault detected - short circuit / open circuit
E 39 E139 M I D R A N G E V 5 B M200 Mid range solenoid V5B fault detected - short circuit / open circuit
E 40 E140 H I G H R A N G E V 5 A High range solenoid V5A fault detected - short circuit / open circuit
E 41 E141 R E E L A F T V 2 C Reel aft solenoid V2C fault detected - short circuit / open circuit
E 42 E142 R E E L F O R E V 4 C Reel fore solenoid V4C fault detected - short circuit / open circuit
E 43 E143 R E E L U P / D O W N V 4 B Reel up / down solenoid V4B fault detected - short circuit / open circuit
E 44 E144 F L O A T R H S V 7 B RHS float solenoid V7B fault detected - short circuit / open circuit
E 45 E145 F L O A T L H S V 7 A LHS float solenoid V7A fault detected - short circuit / open circuit
E 46 S E N S O R V O L T S H I G H Sensor voltage output high.
E 47 S E N S O R V O L T S L O W Sensor voltage output low.
E 48 W C M O V E R T E M P WCM over temp fault.
E 49 W C M L O W T E M P WCM low temp fault.
E 50 B A T T + O U T O F R A N G E System voltage above 16.5 VDC.
E 51 E151 D I S K D R I V E P W M V 8 Disk header drive solenoid V8 fault detected - short circuit / open circuit
E 64 H E A D E R O I L P R E S S U R E Header drive charge pressure low (228)
E 65 K N I F E O V E R L O A D Low knife speed detected < setpoint
E 66 # # . # L O W V O L T S Low system voltage <11.5 VDC
E 67 T R A N S O I L P R E S S U R E Drive supercharge pressure low (202)
E 68 T R A N S O I L T E M P Trans oil temp >221 deg F.
E 69 E N G I N E A I R F I L T E R Engine air filter plugged
E 70 H Y D R A U L I C F I L T E R Hydraulic filter pressure too high. (227)
E 71 L O W H Y D R A U L I C O I L Low hydraulic oil level sensor tripped (225)
E 72 # # . # H I G H V O L T S System voltage above
E101 W C M S P I E R R O R J1939 Can error
E102 W C M C A N E R R O R J1939 Can error
E103 W C M E E R E A D E R R O R Internal error
E104 W C M E E W R I T E E R R O R Internal error
E105 W C M T E M P S E N S O R E R R Internal temperature sensor error.
E N G I N E O I L P R E S S U R E Engine oil pressure warning.
E N G I N E T E M P E R A T U R E Engine coolant temperature warning.
C A N B U S S E R R O R
K N I F E S P D O V E R L O A D Knife speed is < programmed setpoint while header engaged.
N O O P E R A T O R Operator not detected in seat (~3 second delay before message)
N O H E A D E R No header ID detected - not hooked up or wiring error.
L O C K S E A T B A S E Seat base not detected in either Cab or Engine forward position.
D I S E N G A G E H E A D E R Header engage switch on when ignition turned on.
x x x x S x x F x x C Engine code configuration (Canbus)
C E N T E R S T E E R I N G GSL or Pintal switches not closed with the key on / engine off.
N O T I N P A R K GSL or Pintal switches not closed with the key on / engine off.
B R A K E O N Engine running GSL out of "PARK" brake is still engaged.
P L A C E G S L I N T O " N " GSL or Pintal switches not closed with the key on / engine off.
B R A K E S W F A I L U R E Ignition on / engine not running - brake switch and relay closed
B R A K E O F F Engine running - brake solenoid not activated.
C H E C K S E A T S W I T C H E S System detects that both seat switches are active.
C A B F O R W A R D S W O N If both awitches are detected to be activated then the display
E N G F O R W A R D S W O N will alternately flash between these two messages.
Error codes E52 to E63 not allocated
code indicates an OPEN CIRCUIT condition. E41 would be a SHORT in the reel fore / aft solenoid V2C while E141 would indicate an OPEN circuit.
In the case of dual codes being shown for an item (primarily the solenoid valves) the first code indicates a SHORT CIRCUIT condition, while the second
MISC INFORMATION / ERROR CODES
Error codes E73 to E100 not allocated
CDM Error Codes for the M150 / 200 Windrower units