Calculating the initial rate sensor cal – TeeJet TASC-6100 User Manual
Page 37
2-21
98-05018
R2
CE & StandardVersion
TASC 6100
Setup
& Cal.
tion of the fan (spinner) must be entered using the
following procedure:
A. Set the console to the following positions;
1. Power
ON
2. Mode Selector
SET- UP
3. Display Selector
Fan RPM
The current Fan Calibration number is displayed.
B. Use the INC./DEC. switch to set this number to the
desired value.
R
ATE
S
ENSOR
C
ALIBRATION
Calculating The Initial Rate Sensor Cal. #
(Spreader Constant)
It is necessary to enter a Spreader Constant in TASC 6100
to ensure an accurate output from the conveyor. The
spreader constant represents the number of sensor pulses
per cubic foot of material discharged. The constant is
different for different gate settings on adjustable spread-
ers. Constants relating to particular gate settings should
be calibrated and recorded for the spreader.
Calculation of the initial spreader constant requires the
following information:
1) Gate height (H) and width (W) in inches
2) Number of sensor pulses for each revolution of the
spreader rate sensor (P)
3) The distance the conveyor moves during one
revolution of the spreader rate sensor (D), in inches.
Calculate the initial spreader constant as follows:
Where: Ft
3
r
is the volume discharged during each
revolution of the spreader rate sensor, in Cubic Feet.
Continue as follows:
DISPLAY SELECTOR
Speed
Area
Impl. Width
Distance
Test
Speed
PSI/Prime
Total Applied
Application Rate
OFF
SET- UP
DEC.
ON
OPERATE
INC.
Scan
Product Vol.
Fan RPM
BOOMS
1 2 3 4 5 6 7 8 9
% Rate
A-2
B
A-3
A-1
D x W x H
1728
= Ft
3
r
P
Ft
3
r
= Initial Calibration Number (Spreader Constant)
- Sentry 6140
- 801 flowmeter
- GPS Speed Sensor
- IC18 SPREADER JOB COMPUTER
- IC18 SPREADER JOB COMPUTER
- IC18 SPRAYER JOB COMPUTER
- IC18 SPRAYER JOB COMPUTER
- IC18 NH3 JOB COMPUTER
- BOOMPILOT JOB COMPUTER
- BOOMPILOT JOB COMPUTER
- MATRIX 570VT Software version 1.00
- MATRIX 570VT Software version 1.00
- MT 600 Piston Injection Pump
- BoomPilot
- BoomPilot Pro Metric
- BoomPilot Pro
- 500 SLURRY COMPUTER
- 70 Series Speed Area Monitor
- 70 Series EPC - Manual Pump
- 70 Series Fill Flow
- 70 Series Flow Volume Monitor
- ARC-6000
- TASC-6000
- TASC-6200
- TASC-6200
- TASC DATA LOGGER
- TASC PRINTER MODULE
- TASC-6000 Supplement
- 744A Sprayer Control
- 744E AUTO BOOM SECTION CONTROL
- 744E SPRAYER CONTROL
- 814-AB Airblast Sprayer Monitor
- 834 Sprayer Control
- 834 Sprayer Control L2.12
- 834-P Sprayer Control
- 844 Sprayer Control
- 844 Operations Mini
- 844-AB Sprayer Control
- 844-E Sprayer Control
- 844-R Speed Compensated Application Control
- 854 Sprayer Control
- 026 – 73 AddFlow
- LH 3000
- LH 4000
- LH 85
- LH 500
- LH 500
- LH 500
- LH 765
- LH 865
- LH 965
- SENTRY 6510
- Matrix Pro 570GS
- Matrix Pro 570GS
- CenterLine 2.0
- CenterLine v1.05
- CenterLine v1.07
- CenterLine v1.10
- Fieldware SA 2.0 for Legacy 6000
- Swath XL SmartPad II
- Swath XL
- CenterLine Quick Start Guide
- CenterLine with Swath Manager 5
- CenterLine User Guide v2.02
- CenterLine 220 User Guide
- CenterLine 220 User Guide_Metric
- CenterLine 230BP
- CenterLine 230BP
- CenterLine 230BP
- Matrix 570G Reference Guide
- Matrix 570G User Manual
- Matrix 570G User Manual
- Matrix Pro 570G User Manual
- Matrix Pro 570G User Manual
- Matrix Pro 570G Assisted/Auto Steering Setup
- Matrix Pro 570G Assisted/Auto Steering Setup
- Matrix Pro 570G BoomPilot Setup
- Matrix Pro 570G BoomPilot Setup
- Matrix Pro 570G Start Up Guide
- Matrix Pro 570G Start Up Guide
- Matrix 430
- UniPilot
- UniPilot
- Fieldware Link
- Fieldware Link
- RX510
- RX510
- Fieldware Tool
- GuideLine SmartPad II
- RMS Office
- RX370p
- RX375P Receiver
- RX375P Receiver
- RX 400p
- SmartPad II Lightshow User Guide
- SmartPad II Status Detect Guide
- SmartPad II Quick Start Guide
- SmartPad II User Guide
- Tilt Compensation Module Guide_CenterLine
- Tilt Compensation Module Guide_Legacy 6000
- Tilt Compensation Module Guide_SmartPad II
- LH665 VRT
- Legacy 6000 Manual
- Legacy 6000 CAN Guide
- Legacy 6000 Quick Start Guide
- Legacy 6000 RMS_EXT User Guide
- LH 1000
- LH 1200
- LH 1200S
- LH 1200S
- LH 1600M
- LH 1600M
- FOREST LOGGER
- FENDT-INTERFACE
- LH 1600
- LH INTELLITRAM 500
- LH INTELLITRAM 500
- LH Sprimas