TeeJet TASC-6100 User Manual
Page 43
3-1
TASC 6100
Operate
CE & S
TANDARD
V
ERSION
98-05018
R2
Chapter 3 Operation
Normal Start-up and Operation
I
t is important to verify that the control console is
programmed correctly before beginning operations
each day. Refer to Chapter 2 to review the proce-
dures for entering this information.
A. CONSTANTS: Verify that the proper Distance, Flow/
Rate Sensor, and Boom/Spread Width constants are
still entered in the console. It is a good idea to write
these constants down in a convenient location like
the space provided on last page of this manual.
B. APPLICATION RATES: Verify the application rate
settings (Standard Rate & Alternate Rate).
C. ACCUMULATED AREA: If desired, the two acre
accumulators can be reset to zero independently to
allow the tracking of two separate areas.
D. ACCUMULATED VOLUME: Accumulated volume
can be reset to zero. Product Vol. (the count down
register) can be set for the load aboard.
E. The control system is now ready to begin automated
application. Set the Mode Selector switch to the
OPERATE position. Select an appropriate display,
such as Scan.
F. Start the vehicle engine and make sure the pumps
and/or hydraulics are engaged.
G. As you reach the starting point of the first swath, turn
ON the desired Boom switches, and the Master
switch. The TASC 6100 controls application. The
function selected on the Display Selector begins to
register.
H. When you reach the end of the swath, turn OFF the
Boom switches, or Master switch to temporarily stop
application. When the vehicle has been turned and is
ready to start applying on the next swath, turn the
Booms back ON and controlled application resumes.
- Sentry 6140
- 801 flowmeter
- GPS Speed Sensor
- IC18 SPREADER JOB COMPUTER
- IC18 SPREADER JOB COMPUTER
- IC18 SPRAYER JOB COMPUTER
- IC18 SPRAYER JOB COMPUTER
- IC18 NH3 JOB COMPUTER
- BOOMPILOT JOB COMPUTER
- BOOMPILOT JOB COMPUTER
- MATRIX 570VT Software version 1.00
- MATRIX 570VT Software version 1.00
- MT 600 Piston Injection Pump
- BoomPilot
- BoomPilot Pro Metric
- BoomPilot Pro
- 500 SLURRY COMPUTER
- 70 Series Speed Area Monitor
- 70 Series EPC - Manual Pump
- 70 Series Fill Flow
- 70 Series Flow Volume Monitor
- ARC-6000
- TASC-6000
- TASC-6200
- TASC-6200
- TASC DATA LOGGER
- TASC PRINTER MODULE
- TASC-6000 Supplement
- 744A Sprayer Control
- 744E AUTO BOOM SECTION CONTROL
- 744E SPRAYER CONTROL
- 814-AB Airblast Sprayer Monitor
- 834 Sprayer Control
- 834 Sprayer Control L2.12
- 834-P Sprayer Control
- 844 Sprayer Control
- 844 Operations Mini
- 844-AB Sprayer Control
- 844-E Sprayer Control
- 844-R Speed Compensated Application Control
- 854 Sprayer Control
- 026 – 73 AddFlow
- LH 3000
- LH 4000
- LH 85
- LH 500
- LH 500
- LH 500
- LH 765
- LH 865
- LH 965
- SENTRY 6510
- Matrix Pro 570GS
- Matrix Pro 570GS
- CenterLine 2.0
- CenterLine v1.05
- CenterLine v1.07
- CenterLine v1.10
- Fieldware SA 2.0 for Legacy 6000
- Swath XL SmartPad II
- Swath XL
- CenterLine Quick Start Guide
- CenterLine with Swath Manager 5
- CenterLine User Guide v2.02
- CenterLine 220 User Guide
- CenterLine 220 User Guide_Metric
- CenterLine 230BP
- CenterLine 230BP
- CenterLine 230BP
- Matrix 570G Reference Guide
- Matrix 570G User Manual
- Matrix 570G User Manual
- Matrix Pro 570G User Manual
- Matrix Pro 570G User Manual
- Matrix Pro 570G Assisted/Auto Steering Setup
- Matrix Pro 570G Assisted/Auto Steering Setup
- Matrix Pro 570G BoomPilot Setup
- Matrix Pro 570G BoomPilot Setup
- Matrix Pro 570G Start Up Guide
- Matrix Pro 570G Start Up Guide
- Matrix 430
- UniPilot
- UniPilot
- Fieldware Link
- Fieldware Link
- RX510
- RX510
- Fieldware Tool
- GuideLine SmartPad II
- RMS Office
- RX370p
- RX375P Receiver
- RX375P Receiver
- RX 400p
- SmartPad II Lightshow User Guide
- SmartPad II Status Detect Guide
- SmartPad II Quick Start Guide
- SmartPad II User Guide
- Tilt Compensation Module Guide_CenterLine
- Tilt Compensation Module Guide_Legacy 6000
- Tilt Compensation Module Guide_SmartPad II
- LH665 VRT
- Legacy 6000 Manual
- Legacy 6000 CAN Guide
- Legacy 6000 Quick Start Guide
- Legacy 6000 RMS_EXT User Guide
- LH 1000
- LH 1200
- LH 1200S
- LH 1200S
- LH 1600M
- LH 1600M
- FOREST LOGGER
- FENDT-INTERFACE
- LH 1600
- LH INTELLITRAM 500
- LH INTELLITRAM 500
- LH Sprimas