Entering the rate sensor calibration number, Fine tuning the rate sensor cal – TeeJet TASC-6100 User Manual
Page 38
2-22
TASC 6100
98-05018
R2
CE & S
TANDARD
V
ERSION
Entering The Rate Sensor Calibration Number
Enter this calibration number into the console using the
procedure that follows.
A. Set the console to the following positions:
1. Power
ON
2. Mode Selector
SET-UP
3. Display Selector
Total Applied
4. Booms
ON
(If Split Drive option is active)
The current Spreader Constant is displayed.
NOTE: If you have a single conveyor bed, the
"Pump C STnrd" application program must be
selected in order to view or set the Spreader
Constant (See page 2-1)
NOTE: If the console is in Split Drive Mode (Pump
C SPLit), the Spreader Constant can only be viewed
or changed when all programmed booms are on.
B. Use the INC./DEC. switch to set the display to the
calculated Spreader Constant.
Fine Tuning The Rate Sensor cal. #
The accuracy of the Spreader Constant should be verified
and adjusted as necessary. The following procedure is
suggested as a simple means of testing the calibration of
the spreader constant. BE SURE THE PROPER PROD-
UCT DENSITY HAS BEEN ENTERED BEFORE PER-
FORMING THE CALIBRATION OR THE RESULTS
WILL BE INACCURATE.
A. Verify the current Spreader Constant (see previous
page). Record this number for reference.
B. Enter the desired application rate (see page 2-3).
C. Load the vehicle with product of known density.
Be sure the Density is properly entered in the
TASC 6100 (see page 2-20). Use enough material
Mid-T
Mid-T
ech
ech
DISPLAY SELECTOR
Speed
Area
Impl. Width
Distance
Test
Speed
PSI/Prime
Total Applied
Application Rate
OFF
SET- UP
DEC.
ON
OPERATE
INC.
Scan
Product Vol.
Fan RPM
BOOMS
1 2 3 4 5 6 7 8 9
% Rate
A-1
A-2
A-3
B
MASTER
ON
OFF
MI
A-4
If using "Pump C rEFLO"
If using "Pump C STnrd"
Mid-T
Mid-T
ech
ech
- Sentry 6140
- 801 flowmeter
- GPS Speed Sensor
- IC18 SPREADER JOB COMPUTER
- IC18 SPREADER JOB COMPUTER
- IC18 SPRAYER JOB COMPUTER
- IC18 SPRAYER JOB COMPUTER
- IC18 NH3 JOB COMPUTER
- BOOMPILOT JOB COMPUTER
- BOOMPILOT JOB COMPUTER
- MATRIX 570VT Software version 1.00
- MATRIX 570VT Software version 1.00
- MT 600 Piston Injection Pump
- BoomPilot
- BoomPilot Pro Metric
- BoomPilot Pro
- 500 SLURRY COMPUTER
- 70 Series Speed Area Monitor
- 70 Series EPC - Manual Pump
- 70 Series Fill Flow
- 70 Series Flow Volume Monitor
- ARC-6000
- TASC-6000
- TASC-6200
- TASC-6200
- TASC DATA LOGGER
- TASC PRINTER MODULE
- TASC-6000 Supplement
- 744A Sprayer Control
- 744E AUTO BOOM SECTION CONTROL
- 744E SPRAYER CONTROL
- 814-AB Airblast Sprayer Monitor
- 834 Sprayer Control
- 834 Sprayer Control L2.12
- 834-P Sprayer Control
- 844 Sprayer Control
- 844 Operations Mini
- 844-AB Sprayer Control
- 844-E Sprayer Control
- 844-R Speed Compensated Application Control
- 854 Sprayer Control
- 026 – 73 AddFlow
- LH 3000
- LH 4000
- LH 85
- LH 500
- LH 500
- LH 500
- LH 765
- LH 865
- LH 965
- SENTRY 6510
- Matrix Pro 570GS
- Matrix Pro 570GS
- CenterLine 2.0
- CenterLine v1.05
- CenterLine v1.07
- CenterLine v1.10
- Fieldware SA 2.0 for Legacy 6000
- Swath XL SmartPad II
- Swath XL
- CenterLine Quick Start Guide
- CenterLine with Swath Manager 5
- CenterLine User Guide v2.02
- CenterLine 220 User Guide
- CenterLine 220 User Guide_Metric
- CenterLine 230BP
- CenterLine 230BP
- CenterLine 230BP
- Matrix 570G Reference Guide
- Matrix 570G User Manual
- Matrix 570G User Manual
- Matrix Pro 570G User Manual
- Matrix Pro 570G User Manual
- Matrix Pro 570G Assisted/Auto Steering Setup
- Matrix Pro 570G Assisted/Auto Steering Setup
- Matrix Pro 570G BoomPilot Setup
- Matrix Pro 570G BoomPilot Setup
- Matrix Pro 570G Start Up Guide
- Matrix Pro 570G Start Up Guide
- Matrix 430
- UniPilot
- UniPilot
- Fieldware Link
- Fieldware Link
- RX510
- RX510
- Fieldware Tool
- GuideLine SmartPad II
- RMS Office
- RX370p
- RX375P Receiver
- RX375P Receiver
- RX 400p
- SmartPad II Lightshow User Guide
- SmartPad II Status Detect Guide
- SmartPad II Quick Start Guide
- SmartPad II User Guide
- Tilt Compensation Module Guide_CenterLine
- Tilt Compensation Module Guide_Legacy 6000
- Tilt Compensation Module Guide_SmartPad II
- LH665 VRT
- Legacy 6000 Manual
- Legacy 6000 CAN Guide
- Legacy 6000 Quick Start Guide
- Legacy 6000 RMS_EXT User Guide
- LH 1000
- LH 1200
- LH 1200S
- LH 1200S
- LH 1600M
- LH 1600M
- FOREST LOGGER
- FENDT-INTERFACE
- LH 1600
- LH INTELLITRAM 500
- LH INTELLITRAM 500
- LH Sprimas