TeeJet TASC-6100 User Manual
Page 39
2-23
98-05018
R2
CE & StandardVersion
TASC 6100
Setup
& Cal.
to get an accurate measurement but be careful to
keep the conveyor running full. As an example: if
the truck scale reads in 20 lb. (10 Kg.) increments,
at least 1000 lbs. (500Kg.) must be discharged to
be able to calibrate within 2%.
D. Weigh the truck and load and record this weight.
Back up to a location where you can safely unload
the material through the conveyor.
E. Reset the Total Applied accumulator (see page 2-
11).
F. Dispense the desired amount of material by setting
the console switches as follows:
1. Power
ON
2. Mode Selector
OPERATE
3. Display Selector
Test Speed
4. Rate Switch
Standard Rate
5. Programmed Booms
ON
6. Master Switch
ON
The conveyor will start to discharge. Allow the
conveyor to run until the desired amount has been
discharged.
7. Turn OFF the Master switch.
G. Rotate the Display Selector to Total Applied.
TASC 6100 displays the INDICATED AMOUNT
discharged by the conveyor in lbs (Kg.) or tons if
over 20,000 lbs. (metric tons if over 10,000 Kg.).
H. Weigh the truck and load (be sure the driver's
weight is included if he was on the truck when it
was weighed the first time). The difference
between the starting weight and the ending weight
is the ACTUAL AMOUNT discharged by the
conveyor. (This procedure assumes fuel use is
minimal during the test).
I. To adjust the Spreader Constant, use the following
formula:
DISPLAY SELECTOR
Speed
Area
Impl. Width
Distance
Test
Speed
PSI/Prime
Total Applied
Application Rate
OFF
SET- UP
DEC.
ON
OPERATE
INC.
Scan
Product Vol.
Fan RPM
BOOMS
1
2 3 4 5 6 7 8 9
% Rate
F-1
F-2
F-3
B
F-4
MASTER
ON
OFF
MI
F-7
F-6
Alt.-Rate
Standard Rate
OFF
F-4
X Current Spreader Constant = New Spreader Constant
Indicated Amount
Actual Amount
- Sentry 6140
- 801 flowmeter
- GPS Speed Sensor
- IC18 SPREADER JOB COMPUTER
- IC18 SPREADER JOB COMPUTER
- IC18 SPRAYER JOB COMPUTER
- IC18 SPRAYER JOB COMPUTER
- IC18 NH3 JOB COMPUTER
- BOOMPILOT JOB COMPUTER
- BOOMPILOT JOB COMPUTER
- MATRIX 570VT Software version 1.00
- MATRIX 570VT Software version 1.00
- MT 600 Piston Injection Pump
- BoomPilot
- BoomPilot Pro Metric
- BoomPilot Pro
- 500 SLURRY COMPUTER
- 70 Series Speed Area Monitor
- 70 Series EPC - Manual Pump
- 70 Series Fill Flow
- 70 Series Flow Volume Monitor
- ARC-6000
- TASC-6000
- TASC-6200
- TASC-6200
- TASC DATA LOGGER
- TASC PRINTER MODULE
- TASC-6000 Supplement
- 744A Sprayer Control
- 744E AUTO BOOM SECTION CONTROL
- 744E SPRAYER CONTROL
- 814-AB Airblast Sprayer Monitor
- 834 Sprayer Control
- 834 Sprayer Control L2.12
- 834-P Sprayer Control
- 844 Sprayer Control
- 844 Operations Mini
- 844-AB Sprayer Control
- 844-E Sprayer Control
- 844-R Speed Compensated Application Control
- 854 Sprayer Control
- 026 – 73 AddFlow
- LH 3000
- LH 4000
- LH 85
- LH 500
- LH 500
- LH 500
- LH 765
- LH 865
- LH 965
- SENTRY 6510
- Matrix Pro 570GS
- Matrix Pro 570GS
- CenterLine 2.0
- CenterLine v1.05
- CenterLine v1.07
- CenterLine v1.10
- Fieldware SA 2.0 for Legacy 6000
- Swath XL SmartPad II
- Swath XL
- CenterLine Quick Start Guide
- CenterLine with Swath Manager 5
- CenterLine User Guide v2.02
- CenterLine 220 User Guide
- CenterLine 220 User Guide_Metric
- CenterLine 230BP
- CenterLine 230BP
- CenterLine 230BP
- Matrix 570G Reference Guide
- Matrix 570G User Manual
- Matrix 570G User Manual
- Matrix Pro 570G User Manual
- Matrix Pro 570G User Manual
- Matrix Pro 570G Assisted/Auto Steering Setup
- Matrix Pro 570G Assisted/Auto Steering Setup
- Matrix Pro 570G BoomPilot Setup
- Matrix Pro 570G BoomPilot Setup
- Matrix Pro 570G Start Up Guide
- Matrix Pro 570G Start Up Guide
- Matrix 430
- UniPilot
- UniPilot
- Fieldware Link
- Fieldware Link
- RX510
- RX510
- Fieldware Tool
- GuideLine SmartPad II
- RMS Office
- RX370p
- RX375P Receiver
- RX375P Receiver
- RX 400p
- SmartPad II Lightshow User Guide
- SmartPad II Status Detect Guide
- SmartPad II Quick Start Guide
- SmartPad II User Guide
- Tilt Compensation Module Guide_CenterLine
- Tilt Compensation Module Guide_Legacy 6000
- Tilt Compensation Module Guide_SmartPad II
- LH665 VRT
- Legacy 6000 Manual
- Legacy 6000 CAN Guide
- Legacy 6000 Quick Start Guide
- Legacy 6000 RMS_EXT User Guide
- LH 1000
- LH 1200
- LH 1200S
- LH 1200S
- LH 1600M
- LH 1600M
- FOREST LOGGER
- FENDT-INTERFACE
- LH 1600
- LH INTELLITRAM 500
- LH INTELLITRAM 500
- LH Sprimas