B&B Electronics TB5P508SR-2PK - Quick Start Guide - Manual

Documentation Number DRAFT pn#8096R003 VESR9xx-0712qsg
C C h h e e c c k k f f o o r r A A l l l l R R e e q q u u i i r r e e d d H H a a r r d d w w a a r r e e
 Vlinx VESR9xx module
 This Quick Start Guide
 CD with Vlinx Manager s/w and manuals
 Network cable (not included)
 Serial cable(s) (not included)
 10 to 48V DC (6.0W) Power Supply (not
included)
Quick Start
Guide
Vlinx VESR9xx Serial
Servers
1
I I n n s s t t a a l l l l t t h h e e H H a a r r d d w w a a r r e e
2
 Connect a 10 to 48 VDC (58 VDC Max) power supply
(6.0 W required).
 Connect the network cable from the serial server to a
network drop using a standard network cable.
 Connect the serial device(s):
o RS-232 with DB9: straight-through for DCE
device, null modem for DTE device
o RS-232/422/485 with terminal blocks: see
Appendix D for pinouts
UL Installation Information
One Conductor Per Terminal
Use Copper Wire Only
Wire Size: 28 to 16 AWG
Tightening Torque: 5 KG-CM
Wire Temperature Rating: 105 C Minimum (Sized for 60 C
Ampacity)
80 C Maximum Surrounding Ambient Air Temperature
SUITABLE FOR USE IN CLASS 1, DIVISION 2 GROUPS A, B, C, AND D
HAZARDOUS LOCATIONS, OR NONHAZARDOUS LOCATIONS ONLY.
WARNING – EXPLOSION HAZARD – SUBSTITUTION OF ANY
COMPONENT MAY IMPAIR SUITABILITY FOR CLASS 1, DIVISION 2.
L L E E D D S S t t a a t t u u s s
LED STATUS
Ready Blinks if system is operating correctly
Port 1 On indicates serial port open, blinks when data present on
serial port
Port 2 Same as Port 1
(Present on 2 port units only)
Link On indicates Ethernet operating in 100BaseTX, blinks
when data present on Ethernet link
3
M M o o d d e e S S w w i i t t c c h h
Hold in Mode switch for… Result
0 to 2 seconds Initiates a Hardware Reset
2 to 10 seconds Enters Console Mode
More than 10 seconds Resets to Factory Defaults
4
I I n n s s t t a a l l l l V V l l i i n n x x M M a a n n a a g g e e r r S S o o f f t t w w a a r r e e
 Insert the included CD and it should autostart
 Follow the prompts to install the Vlinx Manager
software.
Note: Be sure you have administrative rights & disable firewalls.
5
S S e e t t u u p p V V l l i i n n x x M M a a n n a a g g e e r r S S o o f f t t w w a a r r e e
 Open Vlinx Manager: click
StartProgramsB&B
ElectronicsVlinxVlinx ManagerVESR
Serial Server
 The Discovery page opens
 To configure via the network, select Network.
 If you know the IP address, select The device is
at this address, and type in the address.If not,
select I don’t know the IP address of the device.
 Click Connect.
O O R R … …
S S e e t t u u p p t t h h e e W W e e b b I I n n t t e e r r f f a a c c e e
 Open a browser and type the IP address of the
serial server in the Address Bar.
 When the serial server is found, the
Configuration window appears.
6