Lynx Professional Grills 42" Free Standing Grill L42PSR-1 - Manual (Page 32)


gAs ConneCtions
T
he grill is factory set to use
either propane (lP) or
natural gas (
either propane ( either propane (
nAT). It is critical
either propane ( either propane (
that the gas you use matches
that which the grill was set up
for. You can verify that by
that which the grill was set up that which the grill was set up
checking the rating plate .
The rating plate is located in
one or more of the following
The rating plate is located in The rating plate is located in
places:
Attached to the underside
of the drip tray
on the heat shield behind
the front panel
on the inside left cabinet
wall
►
►
►
The Rating plate lists serial numbers, The Rating plate lists serial numbers,
model numbers and gas type. This model numbers and gas type. This
The Rating plate lists serial numbers, The Rating plate lists serial numbers, The Rating plate lists serial numbers, The Rating plate lists serial numbers, The Rating plate lists serial numbers, The Rating plate lists serial numbers, The Rating plate lists serial numbers,
one is underneath the drip tray. one is underneath the drip tray.
model numbers and gas type. This model numbers and gas type. This model numbers and gas type. This model numbers and gas type. This model numbers and gas type. This model numbers and gas type. This model numbers and gas type. This
Ensure that the gas supplied
meets with the minimum
Ensure that the gas supplied Ensure that the gas supplied
pressure requirements. do not
operate the grill on any gas
pr pressure requirements. essure requirements.
other than that for which the
operate the grill on any gas operate the grill on any gas
grill has been set.
fuel W uel Wc
max
Inlet
Wc min
Under
full Load
nat gas 7 in  in
lP 1 in 11 in in 11 in
Water column Requirements
Both the regulator and the
manifold orifices have been
Both the regulator and the Both the regulator and the
tuned for the type of gas
specified on the rating plate.
tuned for the type of gas tuned for the type of gas
converting to a different type
of gas requires a conversion
onverting to a different type onverting to a different type
kit, available from Lynx or
of gas requires a conversion of gas requires a conversion
from your dealer and must be
kit, available from Lynx or kit, available from Lynx or
installed by a qualified techni-
from your dealer and must be from your dealer and must be
cian.
All installation and all instal-
lation parts must conform to
local codes with the
lation parts must conform to lation parts must conform to
national
lation parts must conform to lation parts must conform to
electrical Code, Ansi/nfPA
70-1990 and the national
fuel gas Code, Ansi Z223.1/
nfPA 54 in the u.s and CgA-
b149.1/.2 in Canada.
canadian installations must
conform to CgA-b149.1/.2
natural gas/propane installa-
tion code. (
natural gas/propane installa- natural gas/propane installa-
c
natural gas/propane installa- natural gas/propane installa-
anada)
natural gas/propane installa- natural gas/propane installa-
nATurAl gAs
Lynx recommends that
only qualified profession-
Lynx recommends that Lynx recommends that
als perform the required
only qualified profession- only qualified profession-
plumbing on this product.
als perform the required als perform the required
To ensure satisfactory per- To ensure satisfactory per To ensure satisfactory per
formance, the gas supply
To ensure satisfactory per To ensure satisfactory per
line must be sized to ac
formance, the gas supply formance, the gas supply
-
commodate the total BTU
requirements of all the gas-
fired equipment that will be
requirements of all the gas- requirements of all the gas-
connected to that line.
fired equipment that will be fired equipment that will be
In no case should pipe less
than 3/4” inside diameter or
In no case should pipe less In no case should pipe less
1” outside diameter ever be
used to connect this product.
calculate the total BTU
output of all equipment
and r
output of all equipment output of all equipment
efer to “
output of all equipment output of all equipment
indeX: g
output of all equipment output of all equipment
as
supply line runs” for
allowable run distances
upply upply
for ¾ inch pipe. failure
to meet these minimum
for ¾ inch pipe. for ¾ inch pipe.
requirements may reduce
performance of the grill
requirements may reduce requirements may reduce
and any other appliances
performance of the grill performance of the grill
running on that supply line.
and any other appliances and any other appliances
Always keep supply line
runs as short as possible.
Always keep supply line Always keep supply line
(see indeX: “bTu output” for
specific model ouputs)
A gas shut-off valve must
be installed in an easily
accessible location by a
qualified plumber.
accessible location by a accessible location by a
►
►
►
warning
Never coNNect a gas liNe directly to the grill. a pressure regulator must be
iNstalled oN all gas equipmeNt. all local codes require it aNd ly ll Nx supplies the
correct regulator with your grill. removiNg or failiNg to iNstall the pressure
regulator caN result iN fire aNd serious persoNal iNjury aNd will void the war-
raNty.