Lynx Professional Grills 42" Free Standing Grill L42PSR-1 - Manual (Page 34)


lP Connections
Make sure the lP cylinder
valve is fully closed. It is
P cylinder P cylinder
possible for the valve to be
valve is fully closed. It is valve is fully closed. It is
open without releasing gas
possible for the valve to be possible for the valve to be
but, as soon as you start con
open without releasing gas open without releasing gas
-
necting the regulator, gas will
leak from the connection.
necting the regulator, gas will necting the regulator, gas will
Insert the regulator inlet into
the cylinder valve and turn the
black coupler clockwise until
the coupler is hand tight.
black coupler clockwise until black coupler clockwise until
do
not over-tighten this connec-
the coupler is hand tight. the coupler is hand tight.
tion.
To disconnect the coupler, first
make sure the main cylinder
To disconnect the coupler, first To disconnect the coupler, first
valve is turned off.
make sure the main cylinder make sure the main cylinder
grasp
the coupler and turn counter
rasp rasp
clockwise. The inlet will then
the coupler and turn counter the coupler and turn counter
disengage.
Always leak-test the connec-
tion after refilling or exchang-
Always leak-test the connec- Always leak-test the connec-
ing lP cylinders. (See IndEX:
“leak Test” for further details.)
gAs line Purging
You should purge the gas line
of air before attempting to
You should purge the gas line You should purge the gas line
light the grill.
of air before attempting to of air before attempting to
make sure all grill controls
are in the “off” position.
Slowly turn on the main
gas supply.
Push in the rotisserie knob
and confirm that the igniter
is glowing. It is furthest
and confirm that the igniter and confirm that the igniter
from the fuel source and
is glowing. It is furthest is glowing. It is furthest
will completely purge the
lines. It will take several
will completely purge the will completely purge the
seconds for the burner to
light.
hold the knob on for
about 20 seconds to allow
the air in the system to
purge and the burner to
light
purge and the burner to purge and the burner to
wait at least 5 minutes
after shutting off the
control before attempting
after shutting off the after shutting off the
to light the burners.
control before attempting control before attempting
►
►
►
►
►
finA in in l Che A A Cks
leAK Tes AK AK Ting
leak test Procedure: tt
create a soapy solution
of 1 part soap and
reate a soapy solution reate a soapy solution

reate a soapy solution reate a soapy solution
parts
water.
Confirm that all control
knobs are in the off
position.
Turn on the fuel supply.
TT for
natural gas, turn the valve
urn on the fuel supply. urn on the fuel supply.
handle 1/4 turn to align
with the gas flow.
handle 1/4 turn to align handle 1/4 turn to align
for l.P., turn the cylinder
valve knob counter
clockwise one full rotation.
Apply the soap solution
generously by paint brush
Apply the soap solution Apply the soap solution
or squirt bottle on all con
generously by paint brush generously by paint brush
-
nections and fittings.
or squirt bottle on all con or squirt bottle on all con
If bubbles appear to
“grow” on any of the con-
If bubbles appear to If bubbles appear to
nections, you have a gas
leak. ImmEdIATELY turn off
nections, you have a gas nections, you have a gas
the gas supply.
fixing a gas leak
Shut off the gas supply
Turn all grill controls to the
“on” position to purge
the grill of any gas build-
” position to purge ” position to purge
up, then turn the controls
back “
up, then turn the controls up, then turn the controls
off
up, then turn the controls up, then turn the controls
”.
►
►
►
►
►
►
►
►
danger! danger!
To prevent fire or explosion To prevent fire or explosion
hazard, DO NOT smoke or hazard, DO NOT smoke or
To prevent fire or explosion To prevent fire or explosion To prevent fire or explosion To prevent fire or explosion To prevent fire or explosion To prevent fire or explosion To prevent fire or explosion
allow any potential source allow any potential source
of ignition (sparks, electri of ignition (sparks, electri
allow any potential source allow any potential source allow any potential source allow any potential source allow any potential source allow any potential source allow any potential source
--
cal arcing, etc) in the area cal arcing, etc) in the area
of ignition (sparks, electri of ignition (sparks, electri of ignition (sparks, electri of ignition (sparks, electri of ignition (sparks, electri of ignition (sparks, electri of ignition (sparks, electri
while performing a leak while performing a leak
cal arcing, etc) in the area cal arcing, etc) in the area cal arcing, etc) in the area cal arcing, etc) in the area cal arcing, etc) in the area cal arcing, etc) in the area cal arcing, etc) in the area
test. Leak tests should be test. Leak tests should be
while performing a leak while performing a leak while performing a leak while performing a leak while performing a leak while performing a leak while performing a leak
conducted outdoors only. conducted outdoors only.
Never conduct a leak test Never conduct a leak test
using fire or flame. using fire or flame.
Wash off the soapy solution
with cold water and dry.
Wash off the soapy solution Wash off the soapy solution
Tighten the loose joint, or
replace the faulty part with
Tighten the loose joint, or Tighten the loose joint, or
manufacturer-recommend-
replace the faulty part with replace the faulty part with
ed replacement parts.
do noT attempt to repair
the l.P. cylinder valve if it is
T attempt to repair T attempt to repair
damaged. The only way to
safely resolve a damaged
damaged. The only way to damaged. The only way to
cylinder is to rePlACe iT.
Repeat the leak test to
ensure that no leaks are
Repeat the leak test to Repeat the leak test to
present.
low heAT burner Ad-
JUSTmEnT
for maIn brass burn-
ers, Prosear™ and sIde
burners!
do not adJust the ro-
tIsserIe burner.
T
he main brass burners and
side burners on your Lynx
grill feature an adjustable low
side burners on your Lynx side burners on your Lynx
setting.
fluctuations in gas pressure,
gas conversion and even in
luctuations in gas pressure, luctuations in gas pressure,
the quality of the gas itself
gas conversion and even in gas conversion and even in
may affect burner perfor
the quality of the gas itself the quality of the gas itself
- may affect burner perfor may affect burner perfor
mance at the “
may affect burner perfor may affect burner perfor
low
may affect burner perfor may affect burner perfor
” setting.
It could be either too high or
too low.
to adjust the burner low tt
setting:
o adjust the burner low o adjust the burner low
make sure the grill is cool.
Remove racks and
briquette trays so that you
can see the flames while
briquette trays so that you briquette trays so that you
adjusting the burners.
Light the burner and set
it to “low”. (all the way
counter- clockwise).
►
►
►
►
►
►
►