Kinze 3110 Mounted Planter Rev. 7/14 - Manual (Page 85)

TM
Model 3110 M0244-01
9/12 5-11
KPM III Monitor Operation
STEP 2 To confirm note below turn knob or use arrow keys
to highlight “OK” button, then press knob or Enter
key to confirm. If single Interplant row is not to be
added select “Cancel” key and press knob or Enter
key to cancel or press ESC key.
STEP 3 To ‘‘Add Single Interplant Row’’ following screen
displays.
If single Interplant row is to be added turn knob or
use arrow keys to highlight “OK” button and then
press knob or Enter key to add Interplant row.
If single Interplant row is not to be added select
Cancel key and press knob or Enter key to cancel or
press ESC key.
STEP 4 ‘‘Sensor Setup’’ screen displays. Plug in new sensor
then scroll down to highlight “Front Row 1” by
turning knob or using arrow keys. Press F1 key next
to Install to learn new sensor.
Status
Plant
About
Setup Mode
Configuration:
Effective row spacing: 15.0
Front / Rear
1. General Settings
2. Seed Meter Settings
3. Row Unit Alarm Levels
4. Setup Data Logging
5. Configure Planter Monitor
6. Add New Muxbus Sensors
7. Add Single Interplant Row
8. Select Speed Sensor
9. Sensor Setup
10.Calibrate Speed Sensor
Logdata
Add Interplant Row
Facing the tractor from behind the planter
add a single interplant row unit to the left
of the existing interplant row units.
Cancel OK
Status
Plant
About
Setup Mode
Configuration:
Effective row spacing: 15.0
Front / Rear
1. General Settings
2. Seed Meter Settings
3. Row Unit Alarm Levels
4. Setup Data Logging
5. Configure Planter Monitor
6. Add New Muxbus Sensors
7. Add Single Interplant Row
8. Select Speed Sensor
9. Sensor Setup
10.Calibrate Speed Sensor
Logdata
Add Single InterPlant Row
Add Single Interplant Row?
Select OK to add the interplant row.
Select Cancel to retain the current
planter monitor configuration.
Cancel OK
Setup Mode Install
Remove
Ignore
Revive
Done
Rear Row 12 OK
Rear Row 11 OK
Rear Row 13 OK
Rear Row 14 OK
Rear Row 15 OK
Rear Row 16 OK
Front Row 2 OK
Front Row 3 OK
Front Row 4 OK
Front Row 5 OK
Front Row 6 OK
Front Row 7 OK
View
Sensor Setup
Front Row 1 none
REPROGRAMMING SPEED SENSOR
This setting must be specified when monitor is first configured. It
must be reprogrammed to use an alternate speed sensor.
NOTE: Speed sensors may not be changed while planting.
RADAR TO MAGNETIC DISTANCE SENSOR
STEP 1 Turn knob or use arrow keys to highlight ‘‘8. Select
Speed Sensor’’. Press knob or Enter key to display
highlighted item.
STEP 2 Press knob or Enter key, a drop down menu appears.
Highlight “Coil Pick-Up” and press knob or Enter key.
STEP 3 Turn knob or use arrow keys to highlight “OK” button
and press knob or Enter key to return to “Setup
Mode” screen.
STEP 4 Turn knob or use arrow keys to highlight “9. Sensor
Setup” and press knob or Enter key.
STEP 5 Unplug radar from tractor.
NOTE: To prevent configuration from being changed select
Cancel, then press rotary encoder knob, Enter key, or ESC
key.
Status
Plant
About
Setup Mode
Configuration:
Effective row spacing: 15.0
Front / Rear
1. General Settings
2. Seed Meter Settings
3. Row Unit Alarm Levels
4. Setup Data Logging
5. Configure Planter Monitor
6. Add New Muxbus Sensors
7. Add Single Interplant Row
8. Select Speed Sensor
9. Sensor Setup
Logdata
10.Calibrate Speed Sensor
Status
Plant
About
Setup Mode
Configuration:
Effective row spacing: 15.0
Front / Rear
1. General Settings
2. Seed Meter Settings
3. Row Unit Alarm Levels
4. Setup Data Logging
5. Configure Planter Monitor
6. Add New Muxbus Sensors
7. Add Single Interplant Row
8. Select Speed Sensor
9. Sensor Setup
Logdata
10.Calibrate Speed Sensor
Select Speed Sensor
Speed Sensor
Cancel OK
Coil Pick-Up
Radar
Radar