LEICA SBP PRO 1 Lithium-Ion Battery for S Typ 007 (7.3V, 2300mAh) - Manual (Page 40)

EN
36
Recor
ding mode
ADDITIONAL FUNCTIONS
USER / APPLICATION-SPECIFIC PROFILES
On the Leica S, any combination of menu settings can be permanently
stored, e.g. so that they can be retrieved quickly and easily at any time
for recurring situations / subjects. A total of four memory slots are
available for these combinations, as well as a factory default setting that
can be retrieved at any time and cannot be changed. You can change the
names of the saved profiles. Profiles set on the camera can be trans-
ferred to one of the memory cards, for example for use in other camera
units, while profiles stored on a card can be transferred onto the camera.
Saving settings / Creating a profile
1. Set the desired functions in the menu
2. In the menu, under SETUP , select the item User Profiles and
3. select Save as User Profile in the sub-menu
• A further sub-menu appears with four lines for the available profile
slots.
4. In this sub-menu, select the desired memory slot
• A corresponding confirmation prompt appears
5. Confirm Yes or cancel No your selection there
• The sub-menu from step 4. appears again, and the selected mem-
ory slot is marked as occupied.
Selecting a profile
1. In the menu, under SETUP , select the item User Profiles and
2. select Load Profile in the sub-menu
• A further sub-menu appears with five lines, the first for the factory
settings, the others for the four profile slots.
Only the lines with occupied profiles can be called up.
3. In this sub-menu, select the desired profile
• The selected profile is marked as active .
Note:
If you change one of the settings for the profile currently in use ---
appears instead of the name of the profile you were previously using in
the initial menu list.
Renaming profiles
1. In the menu, under SETUP , select the item User Profiles, and
2. select Rename User Profile in the sub-menu
• A further sub-menu appears with four lines for the profile slots.
Only the lines with occupied profiles can be called up.
3. Select the desired profile
• A keyboard sub-menu is displayed.
4. First delete the existing designation in the title line there, then select
the desired characters
– Turning the rear thumbwheel or pressing the Joystick to left or
right allows each character to be selected in an endless loop.
– Pressing the Joystick up or down allows you to move between
lines.
– Pressing the rear thumbwheel or the Joystick forward copies the
selected character to the title line.
– Special "buttons":
1 2
4 3
– 1 Switch between capital and small letters
– 2 Delete characters
– 3 Switch between letter and number, or punctuation marks and
special characters
– 4 Spacebar
5. Confirm your inputs with the function keys marked O or OK to the top
right or bottom right of the monitor
• The sub-menu from step 2. appears again, the edited profile has
the new designation.
Saving profiles to a card / transferring profiles from a card
1. In the menu, under SETUP , select the item User Profile and
2. select Import from card or Export to Card in the sub-menu.
• A corresponding confirmation prompt appears
3. Confirm there that you really wish to import or export the profile.
Note:
When exporting, all profile slots are transferred to the card, i.e. including
any empty profiles.
As a result, when importing profiles any existing profiles in the camera
will be overwritten, i.e. deleted.
RESETTING ALL CUSTOM SETTINGS
This function allows you to delete all previous custom settings in the
menu at once, and to reset them to the factory default settings.
Setting the function
1. In the menu, under SETUP , select the item Reset Camera and
2. select No or Yes in the sub-menu.
Note:
This reset also applies to the profiles that may have been created and
saved with Save as User Profile (see left column).
Inhalt_EN.indd 36 12.10.2015 09:34:16