HEIDENHAIN TNC 128 (77184x-02) User Manual
Page 303
![background image](/files/815879/content/doc303.png)
Calibrating a 3-D touch trigger probe (Touch Probe Functions
software option 17)
11.6
11
TNC 128 | User's Manual HEIDENHAIN Conversational Programming | 5/2014
303
The calibration routine varies depending on how your touch probe
can be oriented:
No orientation possible or orientation possible in only one
direction: The TNC executes one approximate and one fine
measurement and determines the effective ball tip radius
(column R in tool.t)
Orientation possible in two directions (e.g. HEIDENHAIN touch
probes with cable): The TNC executes one approximate and
one fine measurement, rotates the touch probe by 180° and
then executes four more probing operations. The center offset
(CAL_OF in tchprobe.tp) is determined in addition to the radius
by probing from opposite orientations.
Any orientation possible (e.g. HEIDENHAIN infrared touch
probes): For probing routine, see "orientation possible in two
directions."
Proceed as follows for manual calibration using a calibration ring:
In the
Manual Operation mode, position the ball tip inside the
bore of the ring gauge
Select the calibration function: Press the
CAL. R
soft key
Enter the diameter of the ring gauge
Enter the safety clearance
New cal. spindle angle: Spindle angle that is used
for the calibration. The TNC uses CAL_ANG from
the touch probe table as a default value. If you
change the value, the TNC saves the value to the
touch probe table during calibration
Start the probing procedure: Press the machine
START button. The 3-D touch probe probes all
required touch points in an automatic probing
routine and calculates the effective ball-tip radius.
If probing from opposite orientations is possible,
the TNC calculates the center offset
Check the results (change the values if required)
Press the
OK soft key for the values to take effect
Press the
END soft key to terminate the calibrating
function
In order to be able to determine the ball-tip center
misalignment, the TNC needs to be specially
prepared by the machine manufacturer. Refer to your
machine manual. Refer to your machine manual.
- TNC 122 User Manual
- TNC 122 Technical Manual
- TNC 360 Service Manual
- TNC 416 Technical Manual
- TNC 335 Technical Manual
- TNC 360 User Manual
- TNC 360 ISO-Programmierung
- TNC 415 (280 540) User Manual
- TNC 370D
- TNC 416
- TNC 416
- TNC 415 (280 540) Technical Manual
- TNC 415 (259 96x) Service Manual
- TNC 407 (280 580) User Manual
- iTNC 530 (340 420) Pilot
- iTNC 530 (340 420) Pilot
- iTNC 530 (340 420) Pilot
- TNC 430 (280 472) Pilot
- iTNC 530 (340 420) Pilot
- iTNC 530 (340 420) Pilot
- iTNC 530 (340 420) Pilot
- iTNC 530 (340 420) Pilot
- TNC 407 (280 580) ISO Programming
- TNC 415 (280 540) Service Manual
- PT 880 Installation
- PT 880 Installation
- ND 523 Installation
- ND 100 User Manual
- ND 287 User Manual
- ND 287 User Manual
- ND 280 Quick Start
- ND 200
- ND 282
- ND 282
- ND 287 Quick Start
- ND 282 B
- ND 281 A
- ND 281 B v.1
- ND 281 B v.2
- ND 221 v.2
- ND 221 v.2
- ND 221 v.2
- ND 221 v.2
- ND 231 B v.2
- ND 231 B v.1
- ND 221 B v.2
- ND 221 B v.2
- ND 550 v.2
- NDP 560
- ND 523
- ND 570
- ND 750 v.2
- ND 750 v.2
- ND 750 v.2
- ND 760 v.3
- ND 760 v.1
- ND 760 v.3
- ND 770 v.1
- ND 770 v.1
- ND 770 v.3
- ND 760 E
- IOB 49
- IOB 49
- NDP 960
- ND 780 Installation
- ND 970
- ND 1100 Quick Start
- ND 1100
- ND 1200
- ND 1200T
- ND 1200 Quick Start
- ND 1200R
- ND 1200R Quick Start
- ND 1300 CNC Setup
- ND 1300 Addendum
- ND 1300 OED and Crosshair Systems
- ND 1300 Quick Start
- ND 1400 Addendum
- ND 1400
- ND 1400 Quick Start
- ND 1300 VED and Crosshair Systems
- ND 2100G
- ND 2100G Installation
- ND 2100G Quick Start
- PT 855 for Milling
- PT 855 for Turning
- PT 880
- MSE 1000
- MSE 1000 Installation
- MSE 1202
- MSE 1350
- MSE 1350
- MSE 1350
- MSE 1350
- MSE 1350
- TS 440
- TS 740
- TS 740
- TS 740
- TS 444
- SE 640
- TS 640
- TT 140
- TT 140
- TL Nano
- TL Nano
- DA 300 TL
- DA 300 TL
- SW 68894x-01 DIN Programming
- SW 54843x-01
- SW 54843x-02
- SW 68894x-02 DIN Programming
- SW 54843x-03
- SW 68894x-03 DIN Programming
- SW 68894x-01
- SW 68894x-02
- SW 68894x-03
- MANUALplus 4110
- MANUALplus 4110 Pilot
- MANUALplus 4110 Instructions for engraving cycles
- CNC Pilot 4290 V7.1
- CNC Pilot 4290 V7.1 Description of B and Y axes
- CNC Pilot 4290
- CNC Pilot 4290 Pilot
- CNC Pilot 4290 Description of the Y axis
- CNC Pilot 4290 Instructions for engraving cycles
- TNC 310 (286 140)
- TNC 310 (286 140)
- TNC 310 (286 140) Pilot
- TNC 310 (286 140) Pilot
- TNC 426 (280 462) Training Basic
- TNC 426 (280 462) Training Basic
- TNC 426 (280 462) Training Basic
- TNC 426 (280 462) Training Advanced
- TNC 426 (280 462) Training Advanced
- TNC 426 (280 462) Training Advanced
- TNC 128 (77184x-01)
- NC 124
- TNC 320 (340 551-01)
- TNC 320 (340 551-02)
- TNC 320 (340 55x-03)
- TNC 620 (340 56x-01) Touch Probe Cycles
- TNC 620 (340 56x-01) Touch Probe Cycles
- TNC 620 (340 56x-01) Touch Probe Cycles
- TNC 320 (340 55x-04)
- TNC 320 (340 55x-04) Cycle programming
- TNC 320 (340 55x-04) ISO programming
- TNC 320 (340 55x-05)
- TNC 320 (340 55x-05) Cycle programming
- TNC 320 (340 55x-05) ISO programming
- TNC 320 (34055x-06)
- TNC 320 (34055x-06) Cycle programming
- TNC 320 (34055x-06) ISO programming
- TNC 320 (77185x-01)
- TNC 320 (77185x-01) Cycle programming
- TNC 320 (77185x-01) ISO programming
- TNC 410
- TNC 430 (280 476) ISO programming
- TNC 430 (280 474)
- TNC 430 (280 474)
- TNC 430 (280 472)
- TNC 430 (280 474)
- TNC 430 (280 474)
- iTNC 530 (340 420) Touch Probe Cycles
- iTNC 530 (340 420) Touch Probe Cycles
- TNC 430 (280 472) Training ISO programming
- TNC 430 (280 476)
- iTNC 530 (340 420)
- iTNC 530 (340 420) ISO programming
- iTNC 530 (340 422)
- iTNC 530 (340 49x-04) Pilot
- iTNC 530 (340 49x-04) Pilot
- iTNC 530 (340 49x-04) Pilot
- iTNC 530 (340 49x-04) Pilot
- iTNC 530 (340 49x-04) Touch Probe Cycles
- iTNC 530 (340 49x-02) Touch Probe Cycles
- iTNC 530 (340 422) ISO programming
- iTNC 530 (340 49x-01)
- iTNC 530 (340 49x-02) Pilot
- iTNC 530 (340 49x-02) Pilot
- iTNC 530 (340 49x-01) ISO programming
- iTNC 530 (340 49x-02)
- iTNC 530 (340 49x-02) ISO programming
- iTNC 530 (340 49x-03)
- iTNC 530 (340 49x-04) Touch Probe Cycles
- iTNC 530 (340 49x-03) smarT.NC Pilot
- iTNC 530 (340 49x-03) ISO programming
- iTNC 530 (340 49x-04)
- iTNC 530 (340 49x-05) Pilot
- iTNC 530 (340 49x-05) Pilot
- iTNC 530 (340 49x-04) ISO programming
- iTNC 530 (340 49x-05)
- iTNC 530 (340 49x-05) Cycle programming
- iTNC 530 (340 49x-05) ISO programming
- iTNC 530 (340 49x-06)
- iTNC 530 (606 42x-01) Cycle programming
- iTNC 530 (340 49x-06) ISO programming
- iTNC 530 (606 42x-01) Pilot
- 530 (340 49x-07)
- iTNC 530 (606 42x-02) Cycle programming
- 530 (340 49x-07) ISO programming
- iTNC 530 (60642x-04) Pilot
- iTNC 530 (60642x-04) Pilot
- iTNC 530 (60642x-04) Pilot
- iTNC 530 (34049x-08)
- iTNC 530 (60642x-03) Cycle programming
- iTNC 530 (34049x-08) ISO programming
- iTNC 530 (606 42x-01)
- iTNC 530 (606 42x-01) ISO programming
- iTNC 530 (606 42x-02)
- iTNC 530 (606 42x-02) ISO programming
- iTNC 530 (60642x-03)
- iTNC 530 (60642x-03) ISO programming
- iTNC 530 (60642x-04)
- iTNC 530 (60642x-04) Cycle programming
- iTNC 530 (60642x-04) ISO programming
- TNC 620 (340 56x-01)
- TNC 620 (340 56x-02)
- TNC 620 (340 56x-02) Cycle programming
- TNC 620 (340 56x-02) ISO programming
- TNC 620 (340 56x-03)
- TNC 620 (73498x-01) Cycle programming
- TNC 620 (340 56x-03) ISO programming
- TNC 620 (34056x-04)
- TNC 620 (73498x-02) Cycle programming
- TNC 620 (34056x-04) ISO programming
- TNC 620 (73498x-01)
- TNC 620 (73498x-01) ISO programming
- TNC 620 (73498x-02)
- TNC 620 (73498x-02) ISO programming
- TNC 620 (81760x-01)
- TNC 620 (81760x-01) Cycle programming
- TNC 620 (81760x-01) ISO programming
- TNC 620 (81760x-02)
- TNC 620 (81760x-02) Cycle programming
- TNC 620 (81760x-02) ISO programming
- TNC 640 (34059x-01)
- TNC 640 (34059x-01) Cycle programming
- TNC 640 (34059x-01) ISO programming
- TNC 640 (34059x-02)
- TNC 640 (34059x-02) Cycle programming
- TNC 640 (34059x-02) ISO programming
- TNC 640 (34059x-04)
- TNC 640 (34059x-04) Cycle programming
- TNC 640 (34059x-04) ISO programming
- TNC 640 (34059x-05)
- TNC 640 (34059x-05) Cycle programming
- TNC 640 (34059x-05) ISO programming
- IK-115
- Length Gauges
- PROFIBUS-DP (DPV0)
- PWM 20
- PWM 20
- PWM 20
- PROFIBUS-DP (DPV2)
- PROFINET