HEIDENHAIN TNC 128 (77184x-02) - Manual (Page 511)

TNC 128 | User's Manual HEIDENHAIN Conversational Programming | 5/2014
511
H
Handwheel............................... 283
Hard disk.................................... 95
Help system............................. 137
Help with error messages........ 131
I
Initiated tools........................... 157
Inserting and modifying blocks... 91
Interrupt machining.................. 334
iTNC 530.................................... 62
L
Linear point patterns................ 387
Load machine configuration..... 370
M
M91, M92................................ 254
Machine parameters for 3D touch
probe........................................ 471
Machine settings...................... 349
Machining pattern.................... 378
Manual datum setting.............. 305
Circle center as datum........... 306
In any axis.............................. 305
Setting a center line as datum 308
Measurement of machining
time.......................................... 327
Measuring workpieces............. 309
M functions
For program run inspection.... 253
For spindle and coolant.......... 253
See miscellaneous functions.. 252
Mid-program startup................ 339
After power failure................. 339
Mirroring................................... 456
Miscellaneous functions.......... 252
enter....................................... 252
For coordinate data................ 254
For path behavior................... 257
Modes of Operation................... 65
MOD function.......................... 346
Exit......................................... 346
Overview................................ 347
Select..................................... 346
Move machine axes
Jog positioning....................... 282
Moving the axes
With machine axis direction
buttons................................... 282
Moving the machine axes........ 282
With the handwheel............... 283
N
NC and PLC synchronization.... 220
NC error messages.................. 131
Nesting..................................... 181
Network connection................. 118
Network settings...................... 361
O
Open BMP file......................... 115
Open GIF file........................... 115
Opening Excel files.................. 111
Opening graphic files............... 115
Opening TXT files.................... 114
Open INI file............................ 114
Open JPG file........................... 115
Open PNG file.......................... 115
Open TXT file........................... 114
Operating times....................... 353
Option number......................... 354
Output of formatted Q
parameters............................... 207
P
Parameter programming:See Q
parameter programming... 190, 236
Part families............................. 193
Path............................................ 98
Pattern definition...................... 378
PDF Viewer.............................. 110
Peck drilling...................... 410, 414
Deepened starting point. 413, 415
Plan view................................. 321
PLC and NC synchronization.... 220
Point tables.............................. 389
Positioning................................ 314
With Manual Data Input......... 314
Positioning logic....................... 473
Preset table...................... 287, 299
Transferring test results.......... 299
Principal axes....................... 81, 81
Probing feed rate..................... 472
Program...................................... 84
Editing...................................... 90
Opening a new program.......... 86
Organization............................. 84
Structuring.............................. 124
Program call............................. 466
Any desired program as
subprogram............................ 179
Via cycle................................. 466
Program defaults...................... 263
Program management:See file
manager..................................... 95
Programming tool movements... 87
Program run............................. 332
Execute.................................. 333
Interrupt................................. 334
Mid-program startup.............. 339
Optional block skip................. 342
Overview................................ 332
Resuming after interruption.... 335
Retraction............................... 337
Program-section repeat............ 177
Projection in three planes......... 321
Q
Q parameter
Export..................................... 221
Transfer values to PLC........... 220
Transfer values to the PLC..... 221
Q parameter programming.... 190,
236
Additional functions................ 202
Angle functions...................... 196
Calculation of circles.............. 197
If-then decisions..................... 198
Mathematical functions.......... 194
Programming notes....
191, 237, 238, 239, 241, 243
Q parameters................... 190, 236
Checking................................ 200
Local parameters QL.............. 190
Nonvolatile parameters QR.... 190
Preassigned............................ 247
R
Radius compensation............... 164
Entering.................................. 165
Rapid traverse.......................... 146
Reading out machine parameters....
244
Reaming................................... 399
Rectangular pocket
Roughing+finishing................ 429
Rectangular stud...................... 433
Reference system................ 81, 81
Replacing texts.......................... 94
Retraction................................. 337
After a power interruption...... 337
Retraction from the contour..... 259
Returning to the contour.......... 341
Rotary axis
Reduce display M94............... 256
S
Scaling...................................... 457
Screen keyboard...................... 122
Screen layout............................. 63
Search function.......................... 93
Selecting the datum................... 82
Selecting the unit of measure.... 86
Select kinematics..................... 350
Setting the BAUD RATE....
355, 356, 356, 356, 356, 357
Single-lip deep-hole drilling....... 414
Software number..................... 354
SPEC FCT................................ 262
Special functions...................... 262
Spindle orientation................... 468
SQL commands....................... 222
Status display....................... 67, 67
Additional................................. 68
General..................................... 67