Cycle parameters – HEIDENHAIN TNC 128 (77184x-02) User Manual
Page 488
![background image](/files/815879/content/doc488.png)
Touch probe cycles
20.9 Measure the tool length and radius (Cycle 483, software option 17
Touch Probe Functions software option 17)
20
488
TNC 128 | User's Manual HEIDENHAIN Conversational Programming | 5/2014
Cycle parameters
Measure tool=0 / Check tool=1: Select whether
the tool is to be measured for the first time or
whether a tool that has already been measured
is to be inspected. If the tool is being measured
for the first time, the TNC overwrites the tool
radius R and the tool length L in the central tool file
TOOL.T by the delta values DR = 0 and DL = 0. If
you wish to inspect a tool, the TNC compares the
measured data with the tool data stored in TOOL.T.
The TNC calculates the deviations and enters them
as positive or negative delta values DR and DL in
TOOL.T. The deviations are also available in the Q
parameters Q115 and Q116. If the delta values are
greater than the permissible tool tolerances for wear
or break detection, the TNC will lock the tool (status
L in TOOL.T).
Clearance height: Enter the position in the spindle
axis at which there is no danger of collision with
the workpiece or fixtures. The clearance height is
referenced to the active workpiece datum. If you
enter such a small clearance height that the tool
tip would lie below the level of the probe contact,
the TNC automatically positions the tool above
the level of the probe contact (safety zone from
safetyDistStylus). Input range -99999.9999 to
99999.9999
Cutter measurement? 0=No / 1=Yes: Choose
whether the control is also to measure the individual
teeth (maximum of 20 teeth)
NC blocks
6 TOOL CALL 12 Z
7 TCH PROBE 483 MEASURE TOOL
Q340=1
;CHECK
Q260=+100
;CLEARANCE HEIGHT
Q341=1
;PROBING THE TEETH
- TNC 122 User Manual
- TNC 122 Technical Manual
- TNC 360 Service Manual
- TNC 416 Technical Manual
- TNC 335 Technical Manual
- TNC 360 User Manual
- TNC 360 ISO-Programmierung
- TNC 415 (280 540) User Manual
- TNC 370D
- TNC 416
- TNC 416
- TNC 415 (280 540) Technical Manual
- TNC 415 (259 96x) Service Manual
- TNC 407 (280 580) User Manual
- iTNC 530 (340 420) Pilot
- iTNC 530 (340 420) Pilot
- iTNC 530 (340 420) Pilot
- iTNC 530 (340 420) Pilot
- TNC 430 (280 472) Pilot
- iTNC 530 (340 420) Pilot
- iTNC 530 (340 420) Pilot
- iTNC 530 (340 420) Pilot
- TNC 407 (280 580) ISO Programming
- TNC 415 (280 540) Service Manual
- PT 880 Installation
- PT 880 Installation
- ND 523 Installation
- ND 100 User Manual
- ND 287 User Manual
- ND 287 User Manual
- ND 280 Quick Start
- ND 200
- ND 282
- ND 282
- ND 287 Quick Start
- ND 282 B
- ND 281 A
- ND 281 B v.1
- ND 281 B v.2
- ND 221 v.2
- ND 221 v.2
- ND 221 v.2
- ND 221 v.2
- ND 231 B v.2
- ND 231 B v.1
- ND 221 B v.2
- ND 221 B v.2
- ND 550 v.2
- NDP 560
- ND 523
- ND 570
- ND 750 v.2
- ND 750 v.2
- ND 750 v.2
- ND 760 v.3
- ND 760 v.1
- ND 760 v.3
- ND 770 v.1
- ND 770 v.1
- ND 770 v.3
- ND 760 E
- IOB 49
- IOB 49
- NDP 960
- ND 780 Installation
- ND 970
- ND 1100 Quick Start
- ND 1100
- ND 1200
- ND 1200T
- ND 1200 Quick Start
- ND 1200R
- ND 1200R Quick Start
- ND 1300 CNC Setup
- ND 1300 Addendum
- ND 1300 OED and Crosshair Systems
- ND 1300 Quick Start
- ND 1400 Addendum
- ND 1400
- ND 1400 Quick Start
- ND 1300 VED and Crosshair Systems
- ND 2100G
- ND 2100G Installation
- ND 2100G Quick Start
- PT 855 for Milling
- PT 855 for Turning
- PT 880
- MSE 1000
- MSE 1000 Installation
- MSE 1202
- MSE 1350
- MSE 1350
- MSE 1350
- MSE 1350
- MSE 1350
- TS 740
- TS 440
- TS 740
- TS 740
- TS 444
- SE 640
- TS 640
- TT 140
- TT 140
- TL Nano
- TL Nano
- DA 300 TL
- DA 300 TL
- SW 68894x-01 DIN Programming
- SW 54843x-01
- SW 54843x-02
- SW 68894x-02 DIN Programming
- SW 54843x-03
- SW 68894x-03 DIN Programming
- SW 68894x-01
- SW 68894x-02
- SW 68894x-03
- MANUALplus 4110
- MANUALplus 4110 Pilot
- MANUALplus 4110 Instructions for engraving cycles
- CNC Pilot 4290 V7.1
- CNC Pilot 4290 V7.1 Description of B and Y axes
- CNC Pilot 4290
- CNC Pilot 4290 Pilot
- CNC Pilot 4290 Description of the Y axis
- CNC Pilot 4290 Instructions for engraving cycles
- TNC 310 (286 140)
- TNC 310 (286 140)
- TNC 310 (286 140) Pilot
- TNC 310 (286 140) Pilot
- TNC 426 (280 462) Training Basic
- TNC 426 (280 462) Training Basic
- TNC 426 (280 462) Training Basic
- TNC 426 (280 462) Training Advanced
- TNC 426 (280 462) Training Advanced
- TNC 426 (280 462) Training Advanced
- TNC 128 (77184x-01)
- NC 124
- TNC 320 (340 551-01)
- TNC 320 (340 551-02)
- TNC 320 (340 55x-03)
- TNC 620 (340 56x-01) Touch Probe Cycles
- TNC 620 (340 56x-01) Touch Probe Cycles
- TNC 620 (340 56x-01) Touch Probe Cycles
- TNC 320 (340 55x-04)
- TNC 320 (340 55x-04) Cycle programming
- TNC 320 (340 55x-04) ISO programming
- TNC 320 (340 55x-05)
- TNC 320 (340 55x-05) Cycle programming
- TNC 320 (340 55x-05) ISO programming
- TNC 320 (34055x-06)
- TNC 320 (34055x-06) Cycle programming
- TNC 320 (34055x-06) ISO programming
- TNC 320 (77185x-01)
- TNC 320 (77185x-01) Cycle programming
- TNC 320 (77185x-01) ISO programming
- TNC 410
- TNC 430 (280 476) ISO programming
- TNC 430 (280 474)
- TNC 430 (280 474)
- TNC 430 (280 472)
- TNC 430 (280 474)
- TNC 430 (280 474)
- iTNC 530 (340 420) Touch Probe Cycles
- iTNC 530 (340 420) Touch Probe Cycles
- TNC 430 (280 472) Training ISO programming
- TNC 430 (280 476)
- iTNC 530 (340 420)
- iTNC 530 (340 420) ISO programming
- iTNC 530 (340 422)
- iTNC 530 (340 49x-04) Pilot
- iTNC 530 (340 49x-04) Pilot
- iTNC 530 (340 49x-04) Pilot
- iTNC 530 (340 49x-04) Pilot
- iTNC 530 (340 49x-02) Touch Probe Cycles
- iTNC 530 (340 49x-04) Touch Probe Cycles
- iTNC 530 (340 422) ISO programming
- iTNC 530 (340 49x-01)
- iTNC 530 (340 49x-02) Pilot
- iTNC 530 (340 49x-02) Pilot
- iTNC 530 (340 49x-01) ISO programming
- iTNC 530 (340 49x-02)
- iTNC 530 (340 49x-02) ISO programming
- iTNC 530 (340 49x-03)
- iTNC 530 (340 49x-04) Touch Probe Cycles
- iTNC 530 (340 49x-03) smarT.NC Pilot
- iTNC 530 (340 49x-03) ISO programming
- iTNC 530 (340 49x-04)
- iTNC 530 (340 49x-05) Pilot
- iTNC 530 (340 49x-05) Pilot
- iTNC 530 (340 49x-04) ISO programming
- iTNC 530 (340 49x-05)
- iTNC 530 (340 49x-05) Cycle programming
- iTNC 530 (340 49x-05) ISO programming
- iTNC 530 (340 49x-06)
- iTNC 530 (606 42x-01) Cycle programming
- iTNC 530 (340 49x-06) ISO programming
- iTNC 530 (606 42x-01) Pilot
- 530 (340 49x-07)
- iTNC 530 (606 42x-02) Cycle programming
- 530 (340 49x-07) ISO programming
- iTNC 530 (60642x-04) Pilot
- iTNC 530 (60642x-04) Pilot
- iTNC 530 (60642x-04) Pilot
- iTNC 530 (34049x-08)
- iTNC 530 (60642x-03) Cycle programming
- iTNC 530 (34049x-08) ISO programming
- iTNC 530 (606 42x-01)
- iTNC 530 (606 42x-01) ISO programming
- iTNC 530 (606 42x-02)
- iTNC 530 (606 42x-02) ISO programming
- iTNC 530 (60642x-03)
- iTNC 530 (60642x-03) ISO programming
- iTNC 530 (60642x-04)
- iTNC 530 (60642x-04) Cycle programming
- iTNC 530 (60642x-04) ISO programming
- TNC 620 (340 56x-01)
- TNC 620 (340 56x-02)
- TNC 620 (340 56x-02) Cycle programming
- TNC 620 (340 56x-02) ISO programming
- TNC 620 (340 56x-03)
- TNC 620 (73498x-01) Cycle programming
- TNC 620 (340 56x-03) ISO programming
- TNC 620 (34056x-04)
- TNC 620 (73498x-02) Cycle programming
- TNC 620 (34056x-04) ISO programming
- TNC 620 (73498x-01)
- TNC 620 (73498x-01) ISO programming
- TNC 620 (73498x-02)
- TNC 620 (73498x-02) ISO programming
- TNC 620 (81760x-01)
- TNC 620 (81760x-01) Cycle programming
- TNC 620 (81760x-01) ISO programming
- TNC 620 (81760x-02)
- TNC 620 (81760x-02) Cycle programming
- TNC 620 (81760x-02) ISO programming
- TNC 640 (34059x-01)
- TNC 640 (34059x-01) Cycle programming
- TNC 640 (34059x-01) ISO programming
- TNC 640 (34059x-02)
- TNC 640 (34059x-02) Cycle programming
- TNC 640 (34059x-02) ISO programming
- TNC 640 (34059x-04)
- TNC 640 (34059x-04) Cycle programming
- TNC 640 (34059x-04) ISO programming
- TNC 640 (34059x-05)
- TNC 640 (34059x-05) Cycle programming
- TNC 640 (34059x-05) ISO programming
- IK-115
- Length Gauges
- PROFIBUS-DP (DPV0)
- PWM 20
- PWM 20
- PWM 20
- PROFIBUS-DP (DPV2)
- PROFINET