Index – Lenze 8400 TopLine User Manual
Page 1755
Lenze · 8400 TopLine · Reference manual · DMS 6.0 EN · 06/2014 · TD05/TD14
1755
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
R
Ramp function generator (L_DFRFG)
Rated device current (C00098)
Rated heat amount of brake resist. (C00131)
Rated motor current (C00088)
Rated motor frequency (C00089)
Rated motor power (C00081)
Rated motor speed (C00087)
Rated motor torque (C00097)
Rated motor voltage (C00090)
Rated power - brake resistor (C00130)
Reduc. brake chopper threshold (C00174)
Reference project
Reference setting
Referencing mode
Remote
Acceleration/deceleration time (C00461)
Control (C00462)
MCK control (C00463)
Monitoring timeout (C00464)
Setpoint selection (C00729)
Reset error message
Reset node (CAN)
Reset reference information
Reset time Imax/M controller (C00074)
Resolver
Phase error (C02863)
Resolver gain (C02862)
Resp. to axis bus error (C00591)
Resp. to brake resist. overtemp. (C00574)
Resp. to CAN bus connection (C00592)
Resp. to CANx_IN monitoring (C00593)
Resp. to communication error with MCI (C01501)
Resp. to control word error (C00594)
Resp. to controller limitations (C00570)
Resp. to DC-bus voltage (C00600)
Resp. to device overload (Ixt) (C00604)
Resp. to earth fault (C00602)
Resp. to fan failure (C00566)
Resp. to feedback (C00603)
Resp. to feedback (C00605)
Resp. to heatsink temp. > shutdown temp. -5°C (C00582)
Resp. to LS_SetError_x (C00581)
Resp. to mains phase failure (C00565)
Resp. to max. freq. feedb. DIG12/67 (C00607)
Resp. to max. speed at switching freq. (C00588)
Resp. to max. speed/output freq. reached (C00579)
Resp. to maximum current (C00609)
Resp. to maximum torque (C00608)
Resp. to motor overload (I²xt) (C00606)
Resp. to motor overtemp. PTC (C00585)
Resp. to motor phase failure (C00597)
Resp. to motor temperature KTY (C00583)
Resp. to open circuit AINx (C00598)
Resp. to open circuit HTL encoder (C00586)
Resp. to operating system error (C00580)
Resp. to peak current (C00569)
Resp. to PLI monitoring (C00643)
Resp. to speed controller limited (C00567)
Resp. to switching frequency reduction (C00590)
Resp. to too frequent AutoFailReset (C00189)
Resp. to wrong controller setting (C00571)
Retracting from limit switches
Reversing the phase sequence
Rotary table application
Rotor displacement angle detection after controller enable
RPDO1 communication parameter (I-1400)
RPDO1 mapping parameter (I-1600)
RPDO2 communication parameter (I-1401)
RPDO2 mapping parameter (I-1601)
RPDO3 communication parameter (I-1402)
RPDO3 mapping parameter (I-1602)
RPDO4 communication parameter (I-1403)
RPDO4 mapping parameter (I-1603)
Running time (C00180)
S
S_ShapingActive (status bit)
Safe stop 1
Safety functions
Safety instructions
Safety module
Saturation characteristic
SC
Depth of current setpoint filter (C00272)
Filter time const. DC detection (C00280)
Freq. current setpoint filter (C00270)
Max. acceleration change (C00274)
max. output voltage (C00276)
Optimisation of field feedforward control (C00576)
Settings (C00079)
Start motor magnetising current (C00918)
Tdn speed controller (C00072)
Tn field controller (C00078)
Tn field weakening controller (C00578)
Vp field controller (C00077)
Vp field weakening controller (C00577)
Width of current setpoint filter (C00271)
Scaling of physical units
Sd10: Speed limit for feedback system 12 (error message)
Sd11: Speed limit for feedback system 67 (error message)
Sd12: Error thermal detector MultiEncoder (error message)
Sd13: Inaccuracy SinCos (error message)
Sd14: Position invalid Hiperface (error message)
Sd2: Open circuit resolver (error message)
Sd3: Feedback system open circuit (error message)
Sd4: Open circuit MultiEncoder (error message)
Sd6: Error thermal detector resolver (error message)
Sd7: Encoder communication (error message)