Lenze 8400 StateLine - Manual (Page 1025)

Lenze · 8400 StateLine · Reference manual · DMS 12.0 EN · 06/2014 · TD05/TD14
1025
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
V/f control (VFCplus + encoder) 154
Motor control (C00006) 601
Motor cosine phi (C00091) 619
Motor current (C00054) 612
Motor data 105
Motor data changeover 577
Motor data parameter list 577
Motor holding brake 402
Motor load monitoring (I2xt) 239
Motor magnetising current (C00095) 620
Motor magnetising inductance (C00092) 619
Motor overcurrent monitoring 241
Motor parameter identification 111
Motor parameter identification is active 87
Motor phase direction of rotation (C00905) 763
Motor phase error monitoring before operation 246
Motor phase failure monitoring 245
Motor phase failure threshold (C00599) 711
Motor rotor resistance (C00082) 618
Motor rotor time constant (C00083) 618
Motor selection 105
Motor speed monitoring 249
Motor stator leakage inductance (C00085) 618
Motor stator resistance (C00084) 618
Motor temperature monitoring (PTC) 242
Motor voltage (C00052) 612
Motorparameter (C00969) 768
Multilingualism 30
N
Network management telegram (NMT) 501
NMT (network management) 501
Node address 497
Node ID 497
Number of CAN SDO channels (C00366) 672
Number of encoder increments (C00420) 680
O
O1U
Gain (C00434) 681
Input value (C00439) 681
Offset (C00435) 681
Voltage (C00436) 681
oC1: Power section - short circuit (error message) 456
oC10: Maximum current reached (error message) 457
oC11: Clamp operation active (error message) 459
oC12: I2xt overload - brake resistor (error message) 458
oC13: Maximum current for Fch exceeded (error message) 459
oC14: Direct-axis current controller limitation (error message)
460
oC15: Cross current controller limitation (error message) 460
oC16: Torque controller limitation (error message) 460
oC17: Clamp sets pulse inhibit (error message) 457
oC2: Power section - earth fault (error message) 456
oC5: Ixt overload (error message) 455
oC6: I2xt overload - motor (error message) 461
oC7 241
oC7: Motor overcurrent (error message) 455
oH1: Heatsink overtemperature (error message) 454
oH3: Motor temperature (X106) triggered (error message) 454
oH4: Heatsink temp. > shutdown temp. -5°C (error message)
454
Open-circuit monitoring - encoder 250
Operating conditions (CAN on board) 489
Operating mode
Speed follower 400
StandBy 398
Operation with increased rated power 206
Operation with safety module 399
Optical location 83
Optimising the response to setpoint changes (SLVC) 171
Option "Lock bFail at TroubleQSP" 101
Original application|control source (C00008) 604
oS1: Maximum speed limit reached (error message) 457
oS2: Max. motor speed (error message) 457
Oscillation damping 216
Oscillation damping filter time (C00235) 652
Oscillation damping influence (C00234) 652
Oscilloscope function 472
ot1: Maximum torque reached (error message) 455
ot2: Speed controller output limited (error message) 459
oU: DC bus overvoltage (error message) 455
Output frequency (C00058) 613
Output power (C00980) 770
Override point of field weakening (C00080) 617
P
Parameter change-over 577
Parameterisable function blocks 860
Password data (C00505) 697
Password protection 36
PC manual control 67
PDO mapping 505 , 507 , 509 , 511
PDO synchronisation 521
Peak current limitation 123
Phase sequence reversal 219
Plant parameters 110
PLI without motion
Adaptation of ident angle (C02875) 832
Adaptation of time duration (C02872) 831
Ident. el. rotor displ. angle (C02873) 831
Optimisation factor (C02870) 830
Running time (C02871) 830
PLI without motion (C02874) 832
Pole position identification 197
Port block "LP_CanIn1" 505
Port block "LP_CanIn2" 507
Port block "LP_CanIn3" 509