Lenze 8400 HighLine - Manual (Page 1560)

Index
1560
Lenze · 8400 HighLine · Referenzhandbuch · DMS 10.0 EN · 06/2014 · TD05/TD14
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Decel. time - quick stop (C00105) 825
Decoupling AnalogOut (C00441) 889
Defining a user-defined V/f characteristic 168
Defining the current limits 151
Defining the speed limits 151
Del.resp. to fault
DC-bus overvoltage (C00601) 924
Delay (C00983) 1028
Description data (C00199) 851
Device access protection 41
Device commands (C00002) 797
Device overload monitoring (Ixt) 295
Device personalisation 46
Device search function 110
Device status (C00137) 831
Device statuses (LED status display) 617
Device type (I-1000) 743
Device utilisat. threshold (Ixt) (C00123) 828
Device utilisation (Ixt) (C00064) 815
dF10: AutoTrip reset (error message) 662
dF14: SW-HW invalid (error message) 661
dF18: BU RCOM error (error message) 661
dF21: BU watchdog (error message) 661
dF22: CU watchdog (error message) 661
dF25: CU RCOM error (error message) 661
dF26: Appl. watchdog (error message) 661
dF50: Retain error (error message) 662
dF51: CuCcr error (error message) 662
dF52: BuCcr error (error message) 662
dH09: EEPROM power section (error message) 666
dH10: Fan failure (error message) 666
dH68: Adjustment data error CU (error message) 666
dH69: Adjustment data error BU (error message) 666
dH70: ControlUnit is unequal to BaseUnit (error message) 666
DI 1/2 & 6/7
Function (C00115) 826
Diagnosis terminal X400 32
Diagnostic interface (DIAG) 34
Diagnostics X6
Change baud rate (C01903) 1096
Current baud rate (C01905) 1096
Max. baud rate (C01902) 1096
DigInX
Inversion (C00114) 826
Digital terminals
For electrical data see the hardware manual
Input terminals
319
Output terminals 340
Touch probe detection 353
User-defined terminal assignment 361
DigOut decoupling (C00447) 892
DigOut decoupling value (C00448) 893
DigOutX
Inversion (C00118) 827
DIP switch settings 691
Direction of rotation check (manual control) 56
Display details of the current error 620
Display error details 620
Display of internal process factors in application units 1524
Display process factors on the keypad 1524
DIx
Debounce time (C02830) 1137
Level (C00443) 890
DOx
Delay times (C00423) 885
Level (C00444) 891
Drive interface 97
Drive-based safety 508
DRV-ERR (LED) 617
DRV-RDY (LED) 617
E
EASY Starter 31
Elapsed-hour meter (C00178) 847
Electrical data
see hardware manual
E-mail to Lenze 1575
Emergency 739
Emergency operation in case of encoder open circuit 182 , 228 ,
317
Encoder 279 , 281
Encoder evaluation method 279
Encoder evaluation method DigIn12 (C00496) 906
Encoder open-circuit monitoring 307
Encoder scanning time (C00425) 886
Encoder/feedback system 273
Energy display (C00981) 1028
Energy-saving V/f characteristic control (VFCplusEco) 172
Engineer 31
Error detection 735
Error ID 639 , 642
Error information (C00165) 844
Error information text (C00166) 844
Error messages 638
Error messages (short overview) 644
Error messages (system bus) 728
Error number 638 , 641
xx.0111.00002 647
xx.0111.00003 647
xx.0111.00004 648
xx.0111.00006 648
xx.0119.00000 648
xx.0119.00001 648
xx.0119.00015 648
xx.0119.00050 649
xx.0123.00001 649
xx.0123.00007 649
xx.0123.00014 649
xx.0123.00015 650