Table of contents – (continued) – Innotech Genesis V4 System User Manual
Page 6
Installation Instructions for Innotech Genesis Systems
Edition: 011100
ii
TABLE OF CONTENTS – (Continued)
SECTION/PARAGRAPH
PAGE
3-3.2.
GENESIS II MID POINTS CONTROLLER. ............................................ 3-10
3-3.2.1.
Power Input. .................................................................................... 3-11
3-3.2.2.
Digital Inputs. .................................................................................. 3-11
3-3.2.3.
Digital Outputs. ............................................................................... 3-11
3-3.2.4.
Analogue Inputs. ............................................................................. 3-11
3-3.2.5.
Analogue Outputs. .......................................................................... 3-12
3-3.3.
GENESIS I DIGITAL CONTROLLER. .................................................... 3-12
3-3.3.1.
Digital Outputs. ............................................................................... 3-12
3-3.3.2.
Analogue Inputs. ............................................................................. 3-13
3-3.3.3.
Analogue Outputs. .......................................................................... 3-14
3-3.3.4.
LEM Connector. .............................................................................. 3-14
3-4.
WIRING OF EXPANSION MODULES. .............................................................. 3-14
3-4.1.
LOCAL EXPANSION MODULES. ............................................................ 3-14
3-4.1.1.
AIM Analogue Input Modules. ...................................................... 3-15
3-4.1.2.
DIM Digital Input Modules. ........................................................... 3-17
3-4.1.3.
DOM Digital Output Modules. ...................................................... 3-18
3-4.2.
REMOTE EXPANSION MODULES. ........................................................ 3-19
3-4.2.1.
REM Power Connections. .............................................................. 3-19
3-4.2.2.
RS485 Comms Connections. .......................................................... 3-20
3-4.2.3.
RMI Remote Module Interface. ..................................................... 3-21
3-4.2.4.
AI REM Analogue Input Module. ................................................. 3-22
3-4.2.5.
AO REM Analogue Output Module. ............................................ 3-23
3-4.2.6.
IDI REM. Opto Isolated Digital Input Module. .......................... 3-24
3-4.2.7.
DI REM Dry Contact Digital Input Module. ............................... 3-24
3-4.2.8.
DO REM Relay Output Module. ................................................... 3-24
3-4.2.9.
CS REM Control Station Module. ................................................. 3-25
3-4.2.10.
MZS REM Multi Zone Station Module. ....................................... 3-25
3-4.2.11.
MP REM Multipoint Module. ........................................................ 3-25
SECTION 4-COMMISSIONING ...................................................................................... 4-1
4-1.
INTRODUCTION. .................................................................................................. 4-1
4-1.1.
INSPECT THE INSTALLATION. ............................................................. 4-1
4-1.1.1.
Mechanical Inspection. ................................................................... 4-1
4-1.1.2.
Electrical Inspection. ...................................................................... 4-2
4-1.2.
CHECK INPUT AND OUTPUT WIRING. ................................................ 4-2
4-1.2.1.
Checking Power Inputs. ................................................................. 4-2
4-1.2.2.
Checking Digital Input Wiring. ..................................................... 4-5
4-1.2.2.1. External-Source Digital Inputs. ............................................... 4-5
4-1.2.2.2. Internal-Source Digital Inputs. ................................................ 4-7
4-1.2.3.
Checking Digital Output Wiring. .................................................. 4-9
4-1.2.4.
Checking Analogue Input Wiring. ................................................ 4-12