Lenze 8400 - Manual (Page 587)

Lenze · 8400 protec HighLine · Reference manual · DMS 3.0 EN · 03/2013 · TD05
587
9 Diagnostics & error management
9.10 Error messages of the operating system
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
 xx.0145.00014 0x2d0e 11534 dF14: SW/HW invalid Fault -
 xx.0145.00024 0x2d18 11544 dF18: BU RCOM error Fault - 0x6100
 xx.0145.00033 0x2d21 11553 dF21: BU Watchdog Fault - 0x6100
 xx.0145.00034 0x2d22 11554 dF22: CU watchdog Fault - 0x6100
 xx.0145.00025 0x2d19 11545 dF25: CU RCOM error Fault - 0x6100
 xx.0145.00050 0x2d32 11570 dF50: Retain error Fault - 0x6100
 xx.0145.00051 0x2d33 11571 dF51: CuCcr error Fault - 0x6100
 xx.0145.00052 0x2d34 11572 dF52: BuCcr error Fault - 0x6100
 xx.0400.00009 0x1a09 6665 dH09: EEPROM power section Fault - 0x5530
 xx.0400.00016 0x1a10 6672 dH10: Fan failure Warning C00566 0x5000
 xx.0400.00104 0x1a68 6760 dH68: Adjustment data error CU Fault - 0x5530
 xx.0400.00105 0x1a69 6761 dH69: Adjustment data error BU Fault - 0x5530
 xx.0123.00094 0x175e 5982 FC01: Switching frequency reduction No Reaction C00590 0x2000
 xx.0123.00095 0x175f 5983 FC02: Maximum speed for Fchop No Reaction C00588 0xF000
 xx.0123.00099 0x1763 5987 FC03: Field controller limitation No Reaction C00570/4 0xF000
 xx.0123.00057 0x1739 5945 Id1: Motor data identification error Fault - 0xF000
 xx.0123.00058 0x173a 5946 Id3: CINH identification WarningLocked - 0xF000
 xx.0123.00059 0x173b 5947 Id4: Resistance identification error Warning - 0xF000
 xx.0123.00060 0x173c 5948 Id7: Motor control does not match motor data Fault - 0xF000
 xx.0125.00011 0x190b 6411 Io11: DigOut level Warning C00598/3 0xF000
 xx.0123.00145 0x1791 6033 LP1: Motor phase failure No Reaction C00597 0x3000
 xx.0123.00015 0x170f 5903 LU: DC bus undervoltage Trouble C00600/1 0x3100
 xx.0123.00016 0x1710 5904 oC1: Power section - short circuit Fault - 0x2000
 xx.0123.00017 0x1711 5905 oC2: Power section - earth fault Fault - 0x2000
 xx.0119.00050 0x1332 4914 oC5: Ixt overload Fault - 0x2000
 xx.0123.00105 0x1769 5993 oC6: I2xt motor overload Warning C00606 0x2000
 xx.0123.00007 0x1707 5895 oC7: Motor overcurrent Fault - 0x2000
 xx.0123.00030 0x171e 5918 oC10: Maximum current reached Fault C00609 0x2000
 xx.0123.00071 0x1747 5959 oC11: Clamp operation active Fault - 0xF000
 xx.0123.00065 0x1741 5953 oC12: I2xt brake resistor overload Fault - 0xF000
 xx.0123.00090 0x175a 5978 oC13: Maximum current for Fch exceeded Fault - 0xF000
 xx.0123.00096 0x1760 5984 oC14: Direct-axis current controller limitation No Reaction C00570/1 0xF000
 xx.0123.00097 0x1761 5985 oC15: Cross current controller limitation No Reaction C00570/2 0xF000
 xx.0123.00098 0x1762 5986 oC16: Torque controller limitation No Reaction C00570/3 0xF000
 xx.0123.00031 0x171f 5919 oC17: Clamp sets pulse inhibit No Reaction C00569/1 0xF000
 xx.0119.00001 0x1301 4865 oH1: Heatsink overtemperature Fault - 0x4000
 xx.0119.00015 0x130f 4879 oH3: Motor temperature (X21) triggered Fault C00585 0x4000
 xx.0119.00000 0x1300 4864 oH4: Heatsink temp. > shutdown temp. -5°C No Reaction C00582 0x4000
 xx.0119.00016 0x1310 4880 oH5: Brake resistor temperature (X20) tripped No Reaction C00587/1 0x4000
 xx.0123.00032 0x1720 5920 oS1: Maximum speed limit reached No Reaction C00579 0x8400
 xx.0123.00033 0x1721 5921 oS2: Max. motor speed Fault - 0x8400
 xx.0123.00001 0x1701 5889 ot1: Max. torque reached No Reaction C00608 0x8300
 xx.0123.00093 0x175d 5981 ot2: Speed controller output limited No Reaction C00567 0xF000
 xx.0123.00014 0x170e 5902 OU: DC bus overvoltage Trouble - 0x3100
 xx.0144.00001 0x2c01 11265 PS01: No memory module Warning - 0x6300
 xx.0144.00002 0x2c02 11266 PS02: Invalid par. set Fault - 0x6300
 xx.0144.00003 0x2c03 11267 PS03: Invalid device par. set Fault - 0x6300
 xx.0144.00004 0x2c04 11268 PS04: Invalid MCI par. set Fault - 0x6300
 xx.0144.00007 0x2c07 11271 PS07: Invalid memory module par. set Fault - 0x6300
 xx.0144.00008 0x2c08 11272 PS08: Invalid device par. Fault - 0x6300
 xx.0144.00009 0x2c09 11273 PS09: Invalid par. format Fault - 0x6300
Error number Error message Response
(Lenze setting)
can be set in CAN Emergency
Error Code
32 bits 16 bits
hex
16 bits
dec